Mon – Sat · 10:00 am – 7:00 pm

Tool & Die Steel

Cold-work, hot-work, plastic-mould and valve steels – D2, D3, D6, A2, O1 / OHNS, H11, H13, DB6 (1.2714), P20, HCHCr, silver steel, EN 52 and 21-4N – stocked in Mumbai as annealed or pre-hardened round bar, flats, plates and die blocks with mill test certificates.

20+ Tool Steel Grades Bar · Flat · Plate · Block EN 10204 3.1 MTC
Tool and die steel components for pressing and moulding
Cold workD2 · D3 · D6 · A2 · O1 / OHNS Hot workH11 · H13 · DB6 · H21 MouldP20 · 1.2738 · 420 · 1.2316
Overview

Steels for Dies, Punches, Moulds & Forming Tools

Tool steels are carbon and alloy steels made to high cleanliness standards and designed to be hardened – to cut, form, blank, extrude, forge or mould other materials. They are grouped by the way they work: cold-work steels (D2, D3, A2, O1) for wear resistance at room temperature, hot-work steels (H11, H13, DB6) that keep strength while in contact with hot metal, and plastic-mould steels (P20, 420) that polish and machine well.

Honesty Impex has stocked tool and alloy steels for toolrooms, die makers, forging shops and mould makers since 2000. Material is held in Mumbai in annealed or pre-hardened condition as rounds, flats, plates and blocks, and supplied cut to size with mill test certificates giving chemistry and hardness.

  • Cold-work, hot-work & mould steels ex-stock
  • Annealed or pre-hardened (P20, DB6) supply
  • Black, peeled, ground or milled surfaces
  • Spectro analysis & hardness certified

Quick Facts

Cold work
D2, D3, D6, A2, O1 / OHNS, S7, HCHCr, silver steel
Hot work
H11, H13, DB6 (1.2714), H21
Mould & special
P20 (1.2311 / 1.2738), 420 (1.2083), 1.2316, EN 52, 21-4N, EN 47
Forms
Round Ø 10 – 500 mm, flats, plates 6 – 400 mm, forged blocks, ground stock
Standards
ASTM A681, EN ISO 4957, DIN 17350, IS 3749, JIS G4404, BS 4659, BS 1407
Certification
EN 10204 3.1 (3.2 with TPI); ultrasonic test on blocks on request

Which Family Do You Need?

Match the steel to the way the tool is loaded. The grade table below gives the detail for each.

FamilyWorking conditionMain propertyTypical grades
Cold-work – high CrBlanking, punching, forming, drawing at room temperatureMaximum wear resistance, dimensional stabilityD2, D3, D6, HCHCr
Cold-work – air / oil hardeningMedium-run dies, gauges, knives, jigsBalance of toughness and wear; low distortionA2, O1 / OHNS, silver steel
Shock-resistingChisels, shear blades, heavy punches, riveting toolsVery high impact toughnessS7
Hot-workDie casting, hot forging, extrusion, hot shearingHot strength, thermal-fatigue (heat-check) resistanceH11, H13, DB6 / 1.2714, H21
Plastic mouldInjection, compression and blow moulds, die holdersMachinability, polishability, pre-hardened supplyP20, 1.2738, 420 / 1.2083, 1.2316
Valve & spring steelsEngine valves, hot bolts, springsOxidation & fatigue resistance at temperatureEN 52, 21-4N, EN 47
Grades & Composition

Tool & Die Steel Grades We Stock

Nominal compositions in weight %, balance iron. Equivalents are the closest common designations; order to the standard and grade you need.

GradeEquivalents – W.Nr / EN · BS · JIS · OtherNominal CompositionTypical HardnessTypical Uses
D21.2379 X153CrMoV12 · BD2 · SKD11 · HCHCrC 1.55, Cr 12, Mo 0.8, V 0.958 – 62 HRCLong-run blanking & punching dies, thread-rolling dies, deep-drawing & extrusion tools, cold rolls, shear blades, gauges
D31.2080 X210Cr12 · BD3 · SKD1 · HCHCrC 2.0, Cr 1260 – 64 HRCHighest wear resistance of the group: blanking dies for thin abrasive stock, drawing dies, burnishing tools, bricks & ceramic dies
D61.2436 X210CrW12 · BD6 · SKD2C 2.1, Cr 12, W 0.760 – 63 HRCD3 with tungsten for extra wear; cutting & stamping tools, drawing dies, cold rolls, measuring tools
A21.2363 X100CrMoV5 · BA2 · SKD12C 1.0, Cr 5.2, Mo 1.1, V 0.257 – 62 HRCAir-hardening, low distortion: medium-run blanking dies, punches, trimming dies, shear blades, forming rolls, gauges
O1 / OHNS1.2510 100MnCrW4 · BO1 · SKS3 · IS T110W2Cr1C 0.95, Mn 1.1, Cr 0.5, W 0.5, V 0.158 – 63 HRCOil-hardening general-purpose tool steel: gauges, jigs, press tools, knives, bushes, collets, master tools
S7≈ 1.2355 · 50CrMoV13-15C 0.5, Cr 3.25, Mo 1.4, V 0.2554 – 58 HRCShock-resisting: chisels, rivet sets, heavy punches, shear blades, plastic moulds needing toughness, cold-forging dies
H111.2343 X37CrMoV5-1 · BH11 · SKD6C 0.38, Si 1.0, Cr 5.0, Mo 1.3, V 0.446 – 54 HRCHot-work with best toughness: extrusion mandrels & containers, hot-heading & bolt-making tools, die-casting dies, aircraft structural parts
H131.2344 X40CrMoV5-1 · BH13 · SKD61 · IS T35Cr5MoV1C 0.40, Si 1.0, Cr 5.2, Mo 1.3, V 1.044 – 52 HRCThe standard hot-work steel: aluminium & zinc die-casting dies, hot forging dies, extrusion dies, hot shear blades, plastic moulds
DB6 / 1.27141.2714 55NiCrMoV7 · BH224/5 · SKT4 · L6 typeC 0.55, Cr 1.1, Mo 0.5, Ni 1.7, V 0.138 – 44 HRC (pre-hardened 350 – 400 HB)Hammer & press forging die blocks, die holders, hot shear blades, pressure-casting moulds for lead/zinc, cold work needing toughness
H211.2581 X30WCrV9-3 · BH21 · SKD5C 0.30, Cr 2.7, W 9.0, V 0.446 – 52 HRCTungsten hot-work steel for the highest die temperatures: brass & copper extrusion dies, hot punches, pressing mandrels
P201.2311 40CrMnMo7 · 1.2738 40CrMnNiMo8-6-4 (Ni) · AISI P20 / P20+NiC 0.40, Cr 1.9, Mn 1.5, Mo 0.2 (+ Ni 1.0 for 1.2738)Pre-hardened 280 – 325 HBInjection & blow moulds, mould bases, die holders, frames, cores, zinc die-casting dies; 1.2738 for large blocks (through-hardened)
420 Mould Steel1.2083 X40Cr14 · 1.2316 X38CrMo16 · SUS420J2C 0.40, Cr 13 – 16, (Mo 1.0 in 1.2316)48 – 52 HRC (1.2316 pre-hard 300 HB)Corrosion-resistant moulds for PVC, acetate and medical & optical parts; high-polish lens and cosmetic-packaging moulds
Silver SteelBS 1407 · ≈ 1.2210 115CrV3 · W1 / W2 typeC 1.15, Mn 0.3, Cr 0.4, Si 0.362 – 64 HRCBright precision-ground round bar (h8): punches, pins, shafts, ejector pins, small tools, model & instrument making
EN 521.4718 X45CrSi9-3 · AISI HNV3 · SUH1 · IS 45Cr9Si4C 0.45, Si 3.0, Cr 9.0Hardened 30 – 38 HRCIntake valves, hot bolts & studs, stems of bi-metal valves, furnace components
21-4N1.4871 X53CrMnNiN21-9 · AISI EV8 · SUH35C 0.53, Mn 9.0, Cr 21, Ni 4, N 0.4Solution treated ≈ 300 HB; aged to 34 HRCHighly stressed exhaust & intake valves, valve seats, hot fasteners, turbocharger parts
EN 47 / SUP101.8159 51CrV4 · SAE 6150 · IS 50Cr1V23C 0.5, Cr 1.0, V 0.15Hardened 44 – 50 HRCHeavy-duty springs, torsion bars, shear blades, hand tools, hot and cold work needing toughness
HCHCrIndian trade term for D2 / D3 (high-carbon high-chromium)C 1.5 – 2.1, Cr 11 – 1358 – 64 HRCGeneral term on Indian drawings for D-series cold-work steel; confirm D2 or D3 at enquiry
Heat Treatment

Hardening & Tempering Guide

Typical values from grade data sheets for the most-used grades. Always follow the heat-treater’s procedure for the actual section size and tool geometry.

GradeSupply conditionHardening °CQuenchTempering °CWorking hardness
D2Annealed ≤ 255 HB1000 – 1040Air, oil or vacuum gas180 – 250 (max wear) or 500 – 540 (toughness)58 – 62 HRC
D3Annealed ≤ 255 HB940 – 970Oil150 – 250, twice60 – 64 HRC
A2Annealed ≤ 241 HB940 – 980Air180 – 230 or 480 – 52057 – 62 HRC
O1 / OHNSAnnealed ≤ 229 HB790 – 820Oil150 – 25058 – 63 HRC
S7Annealed ≤ 229 HB925 – 955Air (oil above 60 mm)200 – 54054 – 58 HRC
H11 / H13Annealed ≤ 229 HB1000 – 1030 / 1020 – 1050Air, pressurised gas or oil550 – 620, 2 – 3 times44 – 52 HRC
DB6 / 1.2714Pre-hardened 350 – 400 HB850 – 880Oil450 – 60038 – 44 HRC
H21Annealed ≤ 235 HB1100 – 1150Oil or air600 – 650, twice46 – 52 HRC
P20 / 1.2738Pre-hardened 280 – 325 HBNormally used as supplied; 840 – 860 if re-hardenedOil550 – 65028 – 34 HRC
420 / 1.2083Annealed ≤ 241 HB1000 – 1050Oil or air200 – 30048 – 54 HRC
Silver steelBright ground, annealed780 – 820Water or oil150 – 30060 – 64 HRC

Pre-heat in steps, hold long enough for the section to soak, and temper immediately after quenching. Nitriding, PVD coating and cryogenic treatment can further extend tool life – ask us for grade data sheets.

Forms & Sizes

Tool Steel Forms Available Ex-Stock

Tool steel is supplied as bar, flat, plate and block. Pipes, fittings and flanges are not made in these grades – see our other materials for those.

ROUND BAR

Round Bar

Hot rolled and forged rounds, black, peeled or centreless ground, for punches, pins, mandrels, shafts and die inserts.

  • Sizes Ø 10 – 500 mm (forged above ~200 mm); silver steel Ø 2 – 100 mm ground h8
  • Grades D2, D3, A2, O1, H11, H13, P20, DB6, EN 52, 21-4N, silver steel
FLAT & SQUARE

Flats & Squares

Rolled and forged flats and squares for knives, shear blades, strippers, guide rails, punches and small dies; precision-ground flat stock on request.

  • Sizes Flats 6 × 25 mm to 150 × 600 mm; squares 20 – 300 mm
  • Grades D2, D3, D6, A2, O1 / OHNS, H13, S7
PLATE & BLOCK

Plates & Die Blocks

Rolled plates and forged, ultrasonically tested die blocks – milled or ground on all six faces to your finished size plus allowance.

  • Sizes Plates 6 – 400 mm thick; blocks to 1000 × 2000 mm, cut to drawing
  • Grades P20 / 1.2738, H13, DB6 / 1.2714, D2, 420 / 1.2316

Density of tool steel is about 7.7 – 7.85 g/cm³. Use the weight calculator for rounds, flats and blocks; remember to add machining allowance to finished dimensions.

Standards

Specifications We Supply To

Tool steels are ordered by grade designation under one of these product standards, with the condition and surface finish specified.

ASTM A681Tool steels – alloy (D, A, O, S, H and P series)
ASTM A686Tool steels – carbon (W series, silver-steel type)
EN ISO 4957Tool steels – cold-work, hot-work and plastic-mould grades (X153CrMoV12, X40CrMoV5-1 …)
DIN 17350Legacy German tool-steel standard; W.Nr 1.2xxx designations still universally used
IS 3749Indian standard for tool & die steels for cold and hot work
JIS G4404Japanese alloy tool steels – SKD, SKT and SKS series
BS 4659 / BS 1407British tool steels (BD2, BH13, BO1 …) / silver steel
EN 10090 / IS 7494Valve steels for internal-combustion engines (EN 52, 21-4N)

See the full standards directory

Applications

Where Tool & Die Steels Are Used

The tooling our customers build – and the grades they ask for.

Blanking & Punching Dies

D2 · D3 · A2 · O1

Drawing & Forming Tools

D2 · D6 · A2 · S7

Die-Casting Dies

H13 · H11 · 1.2343 / 1.2344 ESR

Forging Dies & Hammers

DB6 / 1.2714 · H13 · H21

Extrusion Tooling

H13 · H11 · H21

Plastic Injection Moulds

P20 · 1.2738 · 420 / 1.2083 · 1.2316

Shear Blades & Knives

D2 · S7 · O1 · H13

Engine Valves & Hot Fasteners

EN 52 · 21-4N · EN 47

FAQ

Tool Steel – Common Questions

What to include in an enquiry, and the questions die makers and toolrooms ask us most often.

  1. 1
    Gradee.g. D2 / 1.2379, H13 / 1.2344, P20 / 1.2311 – or the drawing's HCHCr / OHNS / hot-die term
  2. 2
    Form & sizeRound Ø, flat W × T, plate / block T × W × L (finished + allowance)
  3. 3
    ConditionAnnealed or pre-hardened (state HB / HRC); ESR quality if required
  4. 4
    SurfaceBlack, peeled, ground, milled all faces
  5. 5
    Quantity & certificationPieces or kg; EN 10204 3.1 / 3.2, UT report for blocks
  6. 6
    DeliveryDestination and required date

Frequently Asked Questions

D2 or D3 – which should I use?

D3 (2% C, 12% Cr) is slightly harder and more wear-resistant but more brittle, and must be oil quenched. D2 (1.5% C, with Mo and V) air hardens with less distortion, is tougher and can be secondary-hardened at 500 – 540 °C for coating. For most modern blanking and forming dies D2 is the safer choice; D3 suits thin, abrasive stock where chipping is not a risk.

H11 or H13 for die-casting dies?

Both are 5% chromium hot-work steels. H13 has about 1% vanadium, giving higher hot strength and wear resistance and better resistance to heat checking, so it is the usual choice for aluminium and zinc die casting and forging dies. H11, with less vanadium, is tougher and is preferred for extrusion tooling and highly shock-loaded hot tools. For critical dies specify ESR (electro-slag remelted) quality.

What does "pre-hardened" P20 mean?

P20 (1.2311) and its nickel variant 1.2738 are delivered already hardened and tempered to around 280 – 325 HB. The mould is machined directly in this condition and put into service without further heat treatment, avoiding distortion of large cavities. 1.2738 hardens more uniformly through thick sections, so it is specified for big blocks.

What are HCHCr and OHNS on my drawing?

They are Indian trade terms. HCHCr (high-carbon high-chromium) means the D-series – normally D2 or D3, so confirm which. OHNS (oil-hardening non-shrinking) is AISI O1 / W.Nr 1.2510. We stock both and can supply to the exact grade and standard.

Can you supply die blocks machined to size?

Yes. Forged blocks in P20, H13, DB6 and D2 are cut from stock and can be supplied milled or ground on all six faces to your finished dimension plus allowance, with ultrasonic test reports where required.

Get in Touch

Need a Material in a Specific Grade or Size?

Send us the product, grade, size, quantity and delivery location – our team replies with stock status and a competitive quote, usually the same working day.