Mon – Sat · 10:00 am – 7:00 pm

Stainless Steel

Austenitic, ferritic, martensitic and duplex stainless steels stocked in Mumbai since 2000 – 304 / 304L, 316 / 316L, 321, 310S, 904L and duplex 2205 / 2507 – in pipes, tubes, sheets, plates, fittings, flanges, round bars and fasteners.

17+ Grades in Stock All 6 Product Forms MTC EN 10204 3.1
Stainless steel pipes and tubes stacked in the Honesty Impex stockyard
Series200 · 300 · 400 · Duplex · PH Popular304L · 316L · 321 · 310S · 2205 SpecialPVC-coated sheet in 304 & 316
Overview

Corrosion Resistance for Every Service

Stainless steel is an iron alloy with at least 10.5 % chromium. The chromium forms a thin, self-healing oxide film that protects the metal, and additions of nickel, molybdenum, nitrogen and titanium tune that protection for specific media, temperatures and strength levels. Stainless steel is the largest part of our stock – as importers and stockholders we hold it in every one of our six product forms.

The grade families behave very differently: austenitic (300 series) for formability and general corrosion resistance, ferritic (430, 409) for economy, martensitic (410, 420, 431) where hardness is needed, precipitation-hardening (17-4 PH) for very high strength, and duplex (2205, 2507) where chlorides and pressure meet. The table below helps you match the grade to the job.

  • Bulk stock of 304L & 316L in sheet, plate, pipe and bar
  • Speciality: PVC / plastic-coated SS sheet in 304 & 316
  • Mill test certificates EN 10204 3.1 with heat-number traceability
  • Third-party inspection (BV, DNV, LR, TÜV, EIL, IBR) on request

Quick Facts

Families
Austenitic, ferritic, martensitic, PH, duplex & super duplex
Core grades
304 / 304L, 316 / 316L, 321, 347, 310S, 904L, 2205, 2507
Density
7.90 – 8.00 g/cm³ (austenitic), 7.70 (ferritic), 7.80 (duplex)
Service temp.
Cryogenic to 870 °C (321 / 347); 1100 °C for 310S
Forms
Pipe, tube, sheet, plate, coil, fittings, flanges, bar, fasteners
Certification
EN 10204 3.1 / 3.2, PMI, IGC & pitting tests on request
Grades

Stainless Grades We Stock & Supply

Composition values are typical ranges from ASTM A240 / A276; always refer to the specification edition on your purchase order. Other grades can be sourced against order.

Swipe sideways to see all columns.

GradeUNS / ENKey Composition (wt %)PropertiesTypical Use
201 / 202S20100 / S20200
EN 1.4372 / 1.4373
Cr 16–18 · Ni 3.5–6 · Mn 5.5–10Economical chromium-manganese austenitic; high work-hardening; moderate corrosion resistanceUtensils, trim, hollowware, low-cost indoor sheet & tube
304 / 304L / 304HS30400 / S30403 / S30409
EN 1.4301 / 1.4307 / 1.4948
Cr 18–20 · Ni 8–10.5
L: C ≤ 0.03 · H: C 0.04–0.10
The general-purpose grade: excellent formability, weldability and corrosion resistance in most atmospheres and foodsProcess equipment, food & dairy, pharma, architecture, tanks
309SS30908
EN 1.4833
Cr 22–24 · Ni 12–15Oxidation resistance to about 1000 °C; good strength at temperatureFurnace parts, heat-treatment fixtures, kiln linings
310 / 310SS31000 / S31008
EN 1.4841 / 1.4845
Cr 24–26 · Ni 19–22Scaling resistance to about 1100 °C in air; good creep strengthFurnace tubes, radiant tubes, boiler baffles, incinerators
316 / 316L / 316TiS31600 / S31603 / S31635
EN 1.4401 / 1.4404 / 1.4571
Cr 16–18 · Ni 10–14 · Mo 2–3
316Ti: Ti ≥ 5×C
Molybdenum gives pitting and crevice resistance in chlorides; 316L for welded construction, 316Ti for 400–800 °C serviceChemical & pharma plant, marine and coastal work, pulp & paper, textile machinery
317LS31703
EN 1.4438
Cr 18–20 · Ni 11–15 · Mo 3–4Higher Mo than 316L for better pitting resistance in acidic chloride mediaFGD scrubbers, bleach plants, sulphur-bearing process streams
321S32100
EN 1.4541
Cr 17–19 · Ni 9–12 · Ti ≥ 5×CTitanium-stabilised against carbide precipitation; serviceable 425–870 °CExpansion joints, exhaust manifolds, aircraft collector rings, heater tubes
347S34700
EN 1.4550
Cr 17–19 · Ni 9–13 · Nb ≥ 10×CNiobium-stabilised; better creep resistance and weldability than 321 at high temperatureRefinery heaters, high-temperature piping, boiler superheaters
904LN08904
EN 1.4539
Cr 19–23 · Ni 23–28 · Mo 4–5 · Cu 1–2Super-austenitic; resists sulphuric and phosphoric acids and chloride stress-corrosion crackingAcid plants, fertilizer, seawater systems, pharmaceutical reactors
409S40900
EN 1.4512
Cr 10.5–11.75 · Ti stabilisedLow-cost ferritic with good oxidation resistance; weldableAutomotive exhaust, ducting, hoppers
430S43000
EN 1.4016
Cr 16–18 · Ni ≤ 0.75Ferritic, magnetic, not hardenable by heat treatment; good resistance to nitric acid and mild atmospheresAppliances, decorative trim, sugar-mill equipment, dish washers
410S41000
EN 1.4006
Cr 11.5–13.5 · C ≤ 0.15Martensitic; hardenable to about 40 HRC; moderate corrosion resistancePump shafts, valve trim, bolting, steam turbine blades
420S42000
EN 1.4021 / 1.4028
Cr 12–14 · C ≥ 0.15Hardenable to 50+ HRC; best corrosion resistance in the hardened and polished stateCutlery, surgical instruments, shafts, plastic moulds, valve parts
431S43100
EN 1.4057
Cr 15–17 · Ni 1.25–2.5Highest corrosion resistance of the martensitic grades; UTS 850–1000 MPa in the T conditionPump and propeller shafts, marine fasteners, aircraft components
17-4 PHS17400
EN 1.4542
Cr 15–17.5 · Ni 3–5 · Cu 3–5 · NbPrecipitation-hardening; up to 1300 MPa UTS with 304-like corrosion resistancePump shafts, valve stems, aerospace and oil-tool components
Duplex 2205S31803 / S32205
EN 1.4462
Cr 22–23 · Ni 4.5–6.5 · Mo 3–3.5 · N 0.14–0.20Ferritic-austenitic; roughly twice the yield strength of 316L; excellent chloride SCC resistance; PREN ≥ 34Oil & gas, desalination, pressure vessels, chemical tankers, heat exchangers
Super Duplex 2507S32750
EN 1.4410
Cr 24–26 · Ni 6–8 · Mo 3–5 · N 0.24–0.32PREN ≥ 40 for seawater and sour service; very high strengthOffshore piping, seawater pumps, scrubbers, umbilicals
Forms We Supply

Stainless Steel in All Six Product Forms

Standard sizes are held in stock; cutting, polishing and custom lengths are arranged to your drawing.

Swipe sideways to see all columns.

ProductTypes AvailableSize RangeStandards
Pipes & TubesSeamless, ERW & EFW pipe; seamless & welded tube; heat-exchanger, instrumentation & sanitary tube; square & rectangular hollow sectionsNPS ⅛" – 24" · Sch 5S – XXS
Tube OD 6 – 152 mm · wall 0.5 – 12 mm
ASTM A312, A213, A249, A269, A270, A358, A790 / A789
Sheets & PlatesCR sheet & coil (2B, BA, No.4, mirror), HR plate (No.1), PVC / plastic-coated 304 & 316 sheet, chequered & perforated sheet, circlesThickness 0.3 – 120 mm
Widths 1000 / 1250 / 1500 / 2000 mm · cut to size
ASTM A240 / A480, EN 10088-2, IS 6911
FittingsButt-weld elbows, tees, reducers, caps, stub ends; forged socket-weld & threaded fittings; olets; dairy & tube fittingsButt weld ½" – 24" · Forged ⅛" – 4", Class 3000 / 6000 / 9000ASTM A403 (WP), A182 (F), ASME B16.9, B16.11
FlangesWeld neck, slip-on, blind, socket-weld, lap joint, threaded, long weld neck, orifice & spectacle blinds½" – 24" · Class 150 – 2500 · PN 6 – PN 100ASTM A182, ASME B16.5, B16.47, EN 1092-1
Round BarBright drawn, peeled, centreless ground & black (hot-rolled) rounds; also hex, square & flat barØ 3 – 400 mm · lengths 3 – 6 m · cut piecesASTM A276, A479, A564 (17-4 PH), EN 10088-3
FastenersHex bolts, stud bolts, nuts, washers, socket-head screws, U-bolts, anchor fastenersM3 – M64 · ¼" – 2½" · metric & UNC / UNFASTM A193 B8 / B8M, A194 Gr.8 / 8M, F593 / F594, ISO 3506 A2 / A4

Sheet & Tube Finishes

  • No.1 (HRAP)
  • 2D
  • 2B
  • BA
  • No.4 satin
  • Hairline
  • No.8 mirror
  • 180 / 240 / 320 grit
  • PVC-coated
  • Electropolished*

*On request. Coated sheet protects the finish until installation.

Processing

Cutting
Shearing, plasma / laser profiling, saw cutting of bar and pipe
Polishing
Sheet, pipe and bar polished to specified grit
Lengths
Random, fixed or cut-to-length; small lots welcome

Handling & Packing

Segregation
Stainless stored and handled separately from carbon steel to avoid iron contamination
Protection
Interleaving paper or PE film on sheet; end caps on pipe; strapped bundles or crates
Marking
Grade, specification, size and heat number on every item
Standards

Specifications We Supply To

Material is supplied to the specification, grade and edition stated on your purchase order; dual certification (e.g. 316 / 316L, ASTM / EN) is available for most stock.

ASTM A240 / A480Chromium and chromium-nickel stainless steel plate, sheet and strip for pressure vessels and general use
ASTM A312Seamless, welded and heavily cold-worked austenitic stainless steel pipe
ASTM A213 / A249Seamless and welded stainless boiler, superheater and heat-exchanger tubes
ASTM A269 / A270General-service and sanitary stainless tubing
ASTM A790 / A789Seamless and welded duplex and super duplex stainless pipe and tube
ASTM A276 / A479Stainless bars and shapes; bars for boilers and pressure vessels
ASTM A182Forged stainless flanges, fittings and valve parts (F304L, F316L, F51, F53…)
ASTM A403Wrought austenitic stainless butt-weld fittings (WP304L, WP316L…)
ASTM A193 / A194Stainless bolting (B8, B8M) and nuts (Gr.8, 8M) for high-temperature and pressure service
EN 10088-1 / -2 / -3European stainless steel designations, sheet / plate and bar
IS 6911Indian standard for stainless steel plate, sheet and strip
ASME B16.5 / B16.9Dimensions and ratings of flanges and butt-weld fittings

See the full standards directory

Applications

Industries That Rely on Our Stainless Stock

We regularly supply process-equipment fabricators and plant maintenance teams across these sectors, including supplies under third-party inspection.

Chemical & Petrochemical

316L, 317L, 904L and duplex for reactors, columns, piping and storage of corrosive media

Fertilizer Plants

304L / 316L / 904L for urea, ammonia and phosphoric-acid service

Pharma, Food & Dairy

Hygienic 304 / 316L sheet, sanitary tube and fittings with controlled surface finish

Paper & Pulp

316L, 317L and duplex digesters, bleach plant and washer components

Sugar & Cement

304 / 430 sheet for juice heaters, evaporators, chutes and hoppers

Shipbuilding & Marine

316L and duplex for deck fittings, seawater lines and cargo tanks

Pumps & Valves

410, 420, 431, 17-4 PH and duplex bar for shafts, stems, impellers and trim

Construction & Architecture

Cladding, railings, PVC-coated sheet for façades, kitchens and lifts

FAQ & Enquiry

Stainless Steel Questions Answered

Send specification, grade, form, size, quantity and certification needs and we quote accurately – usually the same working day.

  1. 1
    Grade & specificatione.g. ASTM A240 316L or A312 TP304L
  2. 2
    Product formPipe, tube, sheet, plate, fitting, flange, bar or fastener
  3. 3
    SizeThickness × width × length, NPS + schedule, OD × wall or diameter
  4. 4
    Finish2B, BA, No.4, mirror, PVC-coated, polished, pickled
  5. 5
    QuantityPieces, metres, sheets or tonnage
  6. 6
    CertificationEN 10204 3.1 / 3.2, PMI, IGC test, TPI agency
  7. 7
    DeliveryDestination and required date

Frequently Asked Questions

What is the difference between 304 and 316 stainless steel?

316 contains 2–3 % molybdenum, which greatly improves resistance to pitting and crevice corrosion in chlorides – seawater, coastal air, brines and many chemicals. 304 is the economical general-purpose grade for atmospheres, foods and mild chemicals. Both are stocked in L (low carbon) versions.

When should I specify an "L" grade?

The L grades (304L, 316L, 317L) limit carbon to 0.03 % so that welding does not precipitate chromium carbides at the grain boundaries. Specify L whenever the material will be welded and not solution-annealed afterwards. Dual-certified 304/304L and 316/316L material meets both the strength of the standard grade and the chemistry of the L grade.

Is stainless steel magnetic?

Austenitic grades (304, 316, 321, 310) are essentially non-magnetic in the annealed condition, though cold working can make them slightly magnetic. Ferritic (430, 409), martensitic (410, 420, 431) and duplex grades are magnetic. Magnetism is therefore not a reliable test of quality – we supply PMI reports where grade confirmation is required.

When is duplex 2205 a better choice than 316L?

Duplex 2205 has about twice the yield strength of 316L, far better resistance to chloride stress-corrosion cracking and higher pitting resistance (PREN ≥ 34). It is often the economical option for pressure vessels, heat exchangers and seawater piping because thinner sections can be used. Its upper service temperature is limited to about 300 °C.

What is PVC / plastic-coated stainless steel sheet?

It is 304 or 316 sheet, usually in 2B, BA or No.4 finish, supplied with a peel-off protective polyethylene / PVC film on one or both faces. The film protects the decorative surface during cutting, bending, transport and installation and is removed on site. We stock coated sheet in 304 and 316 as a speciality.

Do you supply test certificates and third-party inspection?

Yes. All material is supplied with mill test certificates as per EN 10204 3.1 showing chemistry, mechanical tests and heat number traceability. Type 3.2 certification and inspection by Bureau Veritas, DNV, Lloyd's Register, TÜV, EIL or IBR can be arranged on request.

Get in Touch

Need a Material in a Specific Grade or Size?

Send us the product, grade, size, quantity and delivery location – our team replies with stock status and a competitive quote, usually the same working day.