Mon – Sat · 10:00 am – 7:00 pm

Fasteners

Hex bolts, nuts, stud bolts, washers, socket head cap screws, machine screws, anchor bolts, threaded rods, U-bolts and eye bolts – in stainless steel A2 / A4, ASTM A193 B7 / B8M, property classes 4.6 to 12.9, Monel, Inconel, duplex, titanium, brass and aluminium. M3 to M64, ¼" to 2½", ex-stock Mumbai.

M3 – M64 · ¼" – 2½" 4.6 – 12.9 · B7 · A4-80 EN 10204 3.1 MTC
Stainless and high-tensile bolts, nuts and washers
TypesBolts · Nuts · Studs · Washers · Screws GradesA2-70 · A4-80 · B7 / B8M · 8.8 – 12.9 ThreadsMetric · UNC · UNF · BSW
Overview

Fasteners That Match the Pipe, Flange & Plate

A flange joint is only as good as its bolting, and a stainless vessel loses its corrosion resistance the moment a carbon steel bolt is used on it. That is why we supply fasteners in the same material families as our pipes, plates, fittings and flanges – so one enquiry covers the whole requirement and the grades match from end to end.

Honesty Impex stocks and supplies fasteners from Mumbai as importers, exporters and stockholders since 2000: stainless steel A2-70 / A4-80, high-tensile 8.8 / 10.9 / 12.9, ASTM A193 / A194 flange bolting, and special fasteners in Monel, Inconel, duplex, titanium, brass and aluminium – from a few pieces for maintenance to full project quantities.

  • Stainless, carbon, alloy & non-ferrous fasteners
  • Complete stud-and-nut sets for every flange size
  • Metric, UNC / UNF and BSW threads
  • Test certificates & third-party inspection on request

Quick Facts

Types
Hex bolts, hex nuts, stud bolts, washers, socket head cap screws, machine screws, anchor bolts, threaded rods, U-bolts, eye bolts
Sizes
M3 – M64 metric · ¼" – 2½" imperial
Grades
A2-70, A4-80, B7, B8 / B8M, B16, L7, 2H, 4.6 – 12.9
Threads
Metric coarse & fine, UNC, UNF, BSW, BSF
Coatings
Plain, zinc, hot-dip galvanised, PTFE / xylan, black oxide
Certification
EN 10204 3.1, manufacturer's test certificate, PMI
Fastener Range

Bolts, Nuts, Studs, Washers & Screws

From flange bolting in B7 and B8M to socket screws for tooling and anchor bolts for foundations.

Hex Bolts

Part-thread and full-thread hexagon head bolts and set screws in stainless, high-tensile and alloy steel.

ISO 4014 / 4017 · DIN 931 / 933

Hex Nuts

Standard, heavy hex, thin (jam), nyloc, castle and dome nuts to match the bolting grade.

ISO 4032 · DIN 934 · A194 2H / 8M

Stud Bolts

Fully threaded studs with two heavy hex nuts, supplied as complete sets for ASME B16.5 / B16.47 flange joints.

A193 B7 / B8M + A194 2H / 8M

Washers

Plain, spring, taper, serrated, Belleville and sealing washers – plus machined spacers to drawing.

DIN 125 / 127 · IS 2016 · ASME B18.21.1

Socket Head Cap Screws

Allen cap screws, countersunk, button head, grub (set) screws and shoulder bolts in 12.9 alloy and A2 / A4 stainless.

ISO 4762 · DIN 912 · ASME B18.3

Machine Screws

Pan, cheese, CSK and raised-head machine screws – slotted, Phillips and Torx – in stainless, brass and zinc-plated steel.

ISO 7045 / 7046 · DIN 84 / 85

Anchor & Foundation Bolts

L-type, J-type and plate-anchor foundation bolts, plus expansion and chemical anchors – made to your drawing and length.

IS 5624 · to drawing

Threaded Rods

Fully threaded rod in 1 m and 3 m lengths, or cut to size – stainless, 4.6 / 8.8, B7 and galvanised.

DIN 975 / 976 · ASTM A193

U-Bolts

Round-bend and square-bend U-bolts with plates and nuts for pipe supports, in carbon steel, galvanised and stainless.

To pipe OD · NPS ½" – 24"

Eye Bolts & Eye Nuts

Forged collared eye bolts and eye nuts for lifting and rigging – load rated, in C15 / C35 steel and stainless.

DIN 580 / 582 · IS 4190

Heavy Hex & Lock Nuts

A194 2H / 2HM / 8M heavy hex nuts for stud bolts, plus nyloc, all-metal prevailing-torque and slotted nuts.

ASME B18.2.2 · DIN 985

Special Fasteners

Long studs, tie rods, double-end studs, tap-end studs and made-to-drawing fasteners machined from our own bar stock.

To drawing · with MTC
Grades & Classes

Property Classes & Bolting Grades

The marking on the head tells you the strength – and the nut must match the bolt.

Grade / ClassStandardMinimum tensile · yield / proofMatching nutUsed for
Class 4.6 / 5.6ISO 898-1 / IS 1367-3400 / 500 MPa · 240 / 300 MPaClass 4 / 5Light structural, anchor bolts, general fixing
Class 8.8ISO 898-1 / IS 1367-3800 MPa · 640 MPaClass 8High-tensile structural and machine bolting
Class 10.9ISO 898-11040 MPa · 940 MPaClass 10Heavily loaded joints, machine tools, structures
Class 12.9ISO 898-11220 MPa · 1100 MPaClass 12Socket head cap screws, dies, high-load fixtures
A2-70 (304 / 304L)ISO 3506-1700 MPa · 450 MPa proofA2-70General stainless fastening, food, pharma, outdoor
A4-80 (316 / 316L)ISO 3506-1800 MPa · 600 MPa proofA4-80Marine, chloride and chemical environments
ASTM A193 B7ASTM A193 (AISI 4140)860 MPa · 720 MPa (≤ 2½")A194 2HFlange bolting up to 400 °C – refineries, steam, process
ASTM A193 B7MASTM A193690 MPa · 550 MPa, 235 HBW maxA194 2HMSour service to NACE MR0175 / ISO 15156
ASTM A193 B8 / B8MASTM A193 (304 / 316)Class 1: 515 MPa · Class 2: strain hardenedA194 8 / 8MStainless flange bolting, cryogenic to high temperature
ASTM A193 B16ASTM A193 (CrMoV)860 MPa · 725 MPaA194 4 / 7High-temperature bolting above B7 limits
ASTM A320 L7 / L7MASTM A320860 / 690 MPa, Charpy at −101 °CA194 4 / 7 / 7MLow-temperature and cryogenic service
Duplex / Super DuplexASTM A276 / A479 S31803, S32750620 / 795 MPa · 450 / 550 MPaSame gradeSeawater, desalination, offshore, chemical tankers
Monel 400 / K-500, Inconel 625 / 718ASTM F468 / F467, B164, B446, B637Per alloy and conditionSame alloySevere corrosion, high temperature, sour service
Titanium Gr.2 / Gr.5ASTM F468 / F467, B348345 / 895 MPa · 275 / 828 MPaSame gradeChemical plant, seawater, lightweight assemblies

Property-class values are minimums from ISO 898-1 and ISO 3506-1; ASTM values are for the common size ranges – larger diameters have lower minimums. Always confirm against the current edition of the standard.

Materials

Fasteners in Every Material Family

Match the fastener to the flange, pipe or plate – or to the environment it has to survive.

Material FamilyFastener gradesStandardsTypical Service
Stainless SteelA2-70 / A2-80 (304), A4-70 / A4-80 (316), 316Ti, 321, 410, 17-4PH, B8 / B8M / B8T Class 1 & 2, duplex 2205, super duplex 2507ISO 3506, ASTM A193 / A194 / A320, F593 / F594Process plant, food & pharma, marine, architecture
Carbon SteelClass 4.6, 5.6, 8.8 (medium carbon), A307 Gr. A / B, SAE Gr. 2 / 5, A563 nutsISO 898-1, ASTM A307, A563, SAE J429Structural, machinery, general engineering
Mild SteelClass 4.6 / 4.8 bolts and Class 4 nuts, IS 1363 commercial bolts, foundation bolts, threaded rod, U-boltsIS 1363, IS 1364, IS 5624, DIN 975Civil foundations, pipe supports, fabrication, galvanised fixings
Alloy SteelClass 10.9 / 12.9, A193 B7 / B7M / B16, A320 L7 / L43, A194 2H / 4 / 7, A354 BD, A490ISO 898-1, ASTM A193 / A194 / A320 / A354 / A490Flange bolting, pressure vessels, high-strength structures, tooling
Non-Ferrous MetalsBrass CW614N / C36000, copper, aluminium 6061 / 7075, silicon bronze, Monel 400 / K-500, Inconel 600 / 625 / 718, Hastelloy C-276, titanium Gr.2 / Gr.5ASTM F468 / F467, B164, B446, B637, B348, DIN 931 / 934 in brassElectrical, marine, chemical, high-temperature and lightweight assemblies
Tool & Die SteelMade-to-drawing studs, dowels, clamp bolts and die fixings machined from D2, H13, EN 24 and EN 31 barASTM A681, BS 970Press tools, moulds, jigs and fixtures
Sizes & Threads

Size Range & Thread Forms

State the thread form with the size – an M20 and a ¾" UNC look similar but will not mate.

Size Range

Metric
M3 – M64 (M72 – M100 on request)
Imperial
¼" – 2½" (up to 4" on request)
Bolt length
6 mm – 1 000 mm; longer studs and tie rods to drawing
Threaded rod
1 m and 3 m lengths, or cut to size
Flange stud sets
½" – 60" NPS, Class 150 – 2500, to ASME B16.5 / B16.47 bolt tables

Thread Forms

Metric coarse
ISO 261 / ISO 965 – M3 × 0.5 to M64 × 6
Metric fine
M8 × 1 to M64 × 4 – automotive and hydraulic use
UNC / UNF
ASME B1.1 unified coarse and fine, Class 2A / 2B
BSW / BSF
BS 84 Whitworth – legacy plant and maintenance
8-UN
8-thread series for stud bolts above 1" (ASME B16.5)

Head Markings

ISO classes
8.8, 10.9, 12.9 with manufacturer's mark
Stainless
A2-70, A4-80 etc. per ISO 3506
ASTM
B7, B8M, L7, 2H, 8M plus heat / lot code
Traceability
Marking matched to the test certificate on request

Unmarked high-tensile fasteners should not be used on critical joints – ask us for marked, certified bolting.

Coatings & Finishes

Plain, Plated, Galvanised or PTFE-Coated

The finish decides corrosion life, torque behaviour and whether the nut still runs freely.

SC

Plain / Self Colour

Lightly oiled black or bright finish. Standard for indoor machinery and for stainless, which needs no coating.

  • Corrosion indoor only (carbon / alloy steel)
  • Note stainless is supplied passivated
ZN

Zinc Plated

Electroplated zinc 5 – 12 µm with clear, yellow or black trivalent passivation. Clean appearance, light-duty protection.

  • Standard ISO 4042 / ASTM B633
  • Best for indoor and sheltered outdoor use
HDG

Hot-Dip Galvanised

Dipped in molten zinc for a 45 – 85 µm coating. Nuts are tapped oversize to suit. The standard for outdoor structural and foundation bolts.

  • Standard ISO 10684 / IS 1367-13 / ASTM F2329
  • Best for structures, towers, piping supports outdoors
PTFE

PTFE / Xylan & Black Oxide

Fluoropolymer coating (Xylan 1070 / 1424 or equivalent) over zinc or phosphate gives low, consistent torque and easy break-out after years in service. Black oxide for tooling and socket screws.

  • Best for offshore and refinery flange bolting (B7 / L7)
  • Colour blue, green, red or black to specification
Standards

Specifications We Supply To

A fastener order needs a dimensional standard and a material / property standard.

ISO 4014 / 4017Hex head bolts (part thread) and hex head screws (full thread)
ISO 4032 / 4762Hex nuts style 1; hexagon socket head cap screws
DIN 931 / 933 / 934Hex bolts (part and full thread) and hex nuts
DIN 912 / 125 / 127Socket head cap screws; plain and spring washers
ISO 898-1 / ISO 3506Property classes for carbon / alloy steel and stainless steel fasteners
ASTM A193 / A194 / A320Alloy and stainless bolting and nuts for high-temperature, high-pressure and low-temperature service
ASME B18.2.1 / B18.2.2 / B18.3Square and hex bolts and screws; nuts; socket cap, shoulder and set screws (inch series)
ASME B1.1 / ISO 965Unified inch screw threads; ISO general-purpose metric thread tolerances
IS 1363 / IS 1364Hex head bolts, screws and nuts – product grade C and grades A & B
IS 1367 / IS 2016Technical supply conditions for threaded fasteners; plain washers
BS 3692 / BS 4190ISO metric precision hex bolts, screws and nuts; black hex bolts and nuts
ASTM F468 / F467Non-ferrous bolts, screws, studs and nuts – Monel, Inconel, titanium, brass, aluminium

See the full standards directory

Testing & Inspection

Checked Before Dispatch

Small items matter – a wrong bolt grade can fail a joint as easily as a wrong pipe. Third-party inspection by Bureau Veritas, DNV, Lloyd's Register, TÜV, EIL or IBR can be arranged.

Hardness & Proof Load

Hardness, proof load and wedge tensile tests confirm the property class or ASTM grade supplied.

  • ISO 898-1
  • ASTM F606

Chemical Analysis

Material composition of the heat, reported on the mill or manufacturer's test certificate.

  • ASTM E415
  • EN 10204 3.1

Impact Testing

Charpy V-notch at −101 °C for A320 L7 and other low-temperature bolting grades.

  • ASTM A370
  • ASTM E23

PMI

Positive material identification on stainless, alloy and nickel-alloy fasteners before dispatch.

  • XRF / OES

Thread & Dimensional

Go / no-go thread gauging, length, head and across-flats dimensions checked against the standard.

  • ISO 965 / ASME B1.1
  • ISO 4759

Coating Thickness

Magnetic or XRF measurement of zinc, galvanised and PTFE coating thickness.

  • ISO 1461
  • ISO 2178

Corrosion & Salt Spray

Salt-spray testing of coated fasteners; intergranular corrosion test for stainless bolting on request.

  • ISO 9227
  • ASTM A262

Certification

Mill test certificates to EN 10204 3.1, manufacturer's test reports and 3.2 certificates with third-party inspection.

  • EN 10204
  • TPI
Applications

Where Our Fasteners Are Used

On almost every project we supply – holding the flanges, structures and equipment together.

Flange Bolting

B7 / B8M stud sets with 2H / 8M nuts for piping and vessel joints

Structural Steel

8.8 / 10.9 HSFG bolts, galvanised anchor and foundation bolts

Chemical & Fertilizer Plants

A4-80, duplex, Monel and Hastelloy fasteners for corrosive service

Oil & Gas / Refineries

PTFE-coated B7 / L7 studs, B7M for sour service, Inconel 718

Marine & Shipbuilding

A4 stainless, silicon bronze, cupro-nickel and titanium fasteners

Food, Dairy & Pharma

A2 / A4 stainless bolts, nuts and dome nuts for hygienic equipment

Machine Building & Tooling

12.9 socket screws, shoulder bolts, dowels and clamp bolts

Plant Maintenance

Small lots, replacement sets, BSW and legacy sizes

How to Order

What to Specify in Your Enquiry

Send these details and we can quote accurately – usually the same working day.

  1. 1
    Fastener typeHex bolt, stud bolt, nut, washer, cap screw, anchor bolt, threaded rod…
  2. 2
    Size & lengthThread diameter × length (e.g. M20 × 80) – or flange size and class for stud sets
  3. 3
    Thread formMetric coarse / fine, UNC, UNF, BSW, 8-UN
  4. 4
    Material / gradee.g. A4-80, 8.8, A193 B7, Monel 400
  5. 5
    StandardISO, DIN, ASME, IS, BS – or a drawing for specials
  6. 6
    FinishPlain, zinc, hot-dip galvanised, PTFE / xylan, black oxide
  7. 7
    Quantity & certificationPieces or sets; EN 10204 3.1, PMI, TPI if required

Frequently Asked Questions

Which bolting should I use with my flanges?

For carbon steel flanges in general and high-temperature service, ASTM A193 B7 studs with A194 2H nuts are the usual combination. For stainless piping use B8 or B8M (304 / 316) studs with matching 8 or 8M nuts; for low-temperature service A320 L7 with A194 4 or 7 nuts; and for sour service B7M with 2HM nuts. We supply complete stud-and-nut sets to the ASME B16.5 bolt table for each flange size and class.

What is the difference between A2-70 and A4-80 stainless fasteners?

A2 is 304-type stainless and A4 is 316-type, which contains molybdenum for much better resistance to chlorides – so A4 is the choice near the sea, in swimming pools and in chemical plants. The number is the strength: -70 is 700 MPa minimum tensile, -80 is 800 MPa.

How many stud bolts does a flange need, and what length?

The number, diameter and length come from the bolt table of the flange standard – for example a 4" Class 150 ASME B16.5 flange takes 8 studs of ⅝" × 3¼". Tell us the flange size, class, facing and gasket type and we will supply the correct set; for RTJ or spacer joints the length increases.

Can you supply small quantities?

Yes. Alongside project quantities we supply small lots and single pieces for maintenance and repair work – a few bolts, one stud set, or a metre of threaded rod.

Can you make anchor bolts and special fasteners to drawing?

Yes – L-type, J-type and plate-anchor foundation bolts, long studs, tie rods, double-end studs and made-to-drawing fasteners can be produced in the grade you specify, machined from our own certified bar stock.

Do you supply test certificates for fasteners?

Yes. Fasteners are supplied with the manufacturer's test certificate showing chemistry, hardness and proof load, and with EN 10204 3.1 mill certificates traceable to the heat for A193 / A320 bolting. 3.2 certificates with third-party inspection can be arranged on request.

Get in Touch

Need a Material in a Specific Grade or Size?

Send us the product, grade, size, quantity and delivery location – our team replies with stock status and a competitive quote, usually the same working day.