Mon – Sat · 10:00 am – 7:00 pm

Alloy Steel

Through-hardening, case-hardening and chromium-molybdenum alloy steels – EN 19, EN 24, EN 31, EN 36, 20MnCr5, 8620 and 4130 bars; A335 P11 / P22 / P91 pipe; F11 / F22 flanges and fittings; A387 plate and B7 bolting – imported and stocked in Mumbai with mill test certificates.

16+ Grades in Stock Service to 620 °C (P91) MTC EN 10204 3.1
Alloy steel round bars and rods in stock
BarsEN 19 · EN 24 · EN 31 · EN 36 · 20MnCr5 PipeA335 P5 · P9 · P11 · P22 · P91 ForgedA182 F11 / F22 · A193 B7 / B16
Overview

Strength, Toughness & Heat Resistance by Design

Alloy steels contain deliberate additions of chromium, nickel, molybdenum, manganese, vanadium or aluminium that change how the steel responds to heat treatment. Chromium and molybdenum deepen hardening and add high-temperature strength, nickel adds toughness, vanadium refines grain and resists softening, and aluminium enables nitriding. The result is a family that spans 60 HRC bearing steel, 1500 MPa aircraft-quality bar and creep-resistant boiler pipe.

We stock alloy steel in two broad groups. Engineering bars – EN 19, EN 24, EN 31, EN 36, EN 353, 16MnCr5 / 20MnCr5, 8620, 4130, EN 41B and EN 47 – for shafts, gears, tooling and fasteners. Chrome-moly pressure material – A335 P-grade pipe, A213 T-grade tubes, A182 F-grade flanges and fittings, A234 WP fittings, A387 plate and A193 B7 / B16 bolting – for boilers, refineries and petrochemical plants.

  • EN 19 / EN 24 bars Ø 10 – 600 mm, annealed or hardened & tempered
  • Complete P11 / P22 / P91 line packages – pipe, fittings, flanges, bolting
  • Case-hardening grades for automotive and gear manufacturers
  • Ultrasonic testing, hardness and impact tests arranged on request

Quick Facts

Groups
Through-hardening, case-hardening, nitriding, spring and Cr-Mo pressure steels
Core grades
EN 19, EN 24, EN 31, EN 36, 20MnCr5, 8620, 4130, P11, P22, P91, F22, B7
Strength
UTS 700 – 1550 MPa (bars, heat treated)
Density
7.85 g/cm³
Service temp.
P11 to 540 °C · P22 to 580 °C · P91 to about 620 °C
Certification
EN 10204 3.1 / 3.2, UT, hardness, impact; TPI & IBR on request
Grades

Alloy Steel Grades We Stock & Supply

Compositions are typical ranges from EN 10083 / 10084, ASTM A29 and ASTM A335; mechanical values depend on section size and heat-treatment condition. The specification edition on your order governs.

Swipe sideways to see all columns.

GradeEquivalentsKey Composition (wt %)PropertiesTypical Use
EN 19 · AISI 4140 · 42CrMo4EN 1.7225 · 709M40 · IS 40Cr1Mo28C 0.38–0.45 · Cr 0.90–1.20 · Mo 0.15–0.30Through-hardening Cr-Mo steel; hardened & tempered to 850–1000 MPa (T condition); good toughness and fatigue strengthShafts, gears, studs and bolts (A193 B7), crankshafts, hydraulic rods, tool holders
EN 24 · AISI 4340 · 34CrNiMo6EN 1.6582 · 817M40 · IS 40Ni2Cr1Mo28C 0.36–0.44 · Ni 1.30–1.70 · Cr 1.00–1.40 · Mo 0.20–0.35High-strength Ni-Cr-Mo steel; 1000–1550 MPa with excellent toughness and hardenability in large sectionsHeavy-duty gears, crankshafts, aircraft and gas-turbine parts, press tooling, high-tensile bolts
EN 31 · AISI 52100 · 100Cr6EN 1.3505 · 535A99 · IS 103Cr1C 0.95–1.10 · Cr 1.30–1.60High-carbon chromium bearing steel; 60–64 HRC after hardening; excellent wear resistanceBall and roller bearings, rollers, punches, gauges, dies
EN 36 · 655M13 · 15NiCr13EN 1.5752 · ≈ AISI 3415 / 9315C 0.10–0.18 · Ni 3.00–3.75 · Cr 0.60–1.10Case-hardening Ni-Cr steel; hard case (58–62 HRC) with very tough coreGears, pinions, camshafts, crown wheels, highly stressed automotive transmission parts
EN 353 · 815M17 · 16NiCr4IS 15Ni4Cr1 · ≈ SAE 8617C 0.14–0.20 · Ni 1.20–1.70 · Cr 0.60–1.00 · Mo 0.10–0.20Case-hardening Ni-Cr-Mo steel with good core strengthGears, shafts, pins, sprockets, worm gears
16MnCr5 · 20MnCr5EN 1.7131 · 1.7147 · IS 16Mn5Cr4 / 20Mn5Cr4C 0.14–0.22 · Mn 1.00–1.40 · Cr 0.80–1.10Mn-Cr case-hardening steels, widely used in automotive; distortion-free carburisingGearbox gears, shafts, pins, synchroniser rings, pump components
SAE 8620 · 20NiCrMo2-2EN 1.6523 · 805M20C 0.18–0.23 · Ni 0.40–0.70 · Cr 0.40–0.60 · Mo 0.15–0.25General-purpose case-hardening steel; core strength 700–1000 MPaGears, pinions, cams, ring gears, fasteners, arbors
AISI 4130 · 25CrMo4EN 1.7218 · 708A25C 0.28–0.33 · Cr 0.80–1.10 · Mo 0.15–0.25Weldable low-alloy Cr-Mo steel; normalised ~ 670 MPa, Q&T up to 1000 MPaOil-tool and wellhead components, aircraft tubing, roll cages, pressure components
AISI 4145H / 4145H Mod.—C 0.42–0.49 · Cr 0.75–1.20 · Mo 0.15–0.25Deep-hardening Cr-Mo steel supplied Q&T to API 7-1 requirementsDrill collars, stabilisers, kellys, downhole tools, subs
EN 41B · 905M39 · 41CrAlMo7-10EN 1.8509C 0.35–0.43 · Cr 1.50–1.80 · Al 0.90–1.30 · Mo 0.15–0.25Nitriding steel; surface hardness 950–1100 HV with minimal distortionExtruder screws and barrels, spindles, cylinder liners, gauges, crankshafts
EN 47 · 735A50 · 51CrV4EN 1.8159 · AISI 6150 · IS 50Cr1V23C 0.47–0.55 · Cr 0.90–1.20 · V 0.10–0.25Cr-V spring steel; high fatigue strength after hardening & temperingLeaf and coil springs, torsion bars, spring washers, hand tools
A335 P5 · P9 · P11 · P22 · P91K41545 · K90941 · K11597 · K21590 · K90901P5: 5Cr-0.5Mo · P9: 9Cr-1Mo · P11: 1.25Cr-0.5Mo · P22: 2.25Cr-1Mo · P91: 9Cr-1Mo-V-NbSeamless ferritic alloy pipe for high-temperature service; P91 for creep strength to about 620 °CBoiler main steam and reheat lines, refinery heater coils, hydrocracker and hydrogen service piping
A182 F5 · F9 · F11 · F22 · F91matching P-grade forgings · also A336 F22As the P grades above; F22 Cl.3 normalised & temperedForged flanges, fittings and valve components for high-temperature linesFlanges, forged fittings, valves and nozzles matching A335 pipe
A234 WP5 · WP11 · WP22 · WP91Cl.1 / Cl.2 / Cl.3 by strengthAs the P grades aboveWrought butt-weld fittings, normalised & temperedElbows, tees, reducers and caps for Cr-Mo piping systems
A387 Gr.11 · Gr.22 (Cl.1 / Cl.2)K11789 · K21590 · ≈ 13CrMo4-5 / 10CrMo9-10Gr.11: 1.25Cr-0.5Mo · Gr.22: 2.25Cr-1MoCr-Mo pressure-vessel plate for elevated-temperature and hydrogen serviceReactors, hydrocrackers, heat-exchanger shells, boiler drums
A193 B7 · B7M · B16B7 = 4140 Q&T · B16 = Cr-Mo-VB7: 0.37–0.49 C, 0.75–1.20 Cr, 0.15–0.25 Mo · B16 adds 0.25–0.35 VAlloy bolting; B7 min. UTS 860 MPa (≤ 2½"), B7M hardness-controlled for sour service, B16 for higher temperatureStud bolts and hex bolts for flanged joints, pressure vessels and valves
Forms We Supply

Alloy Steel in All Six Product Forms

Engineering grades are stocked mainly as bar and plate; Cr-Mo pressure grades as matching pipe, fittings, flanges and bolting.

Swipe sideways to see all columns.

ProductTypes AvailableSize RangeStandards
Pipes & TubesSeamless Cr-Mo pipe (P5 / P9 / P11 / P22 / P91), boiler & superheater tubes (T11 / T22 / T91), 4130 mechanical tubing, honed & cold-drawn seamless tubeNPS ½" – 24" · Sch 40 – XXS
Tube OD 19 – 219 mm · wall 2 – 25 mm
ASTM A335, A213, A519, EN 10216-2 (13CrMo4-5, 10CrMo9-10)
Sheets & PlatesCr-Mo pressure-vessel plate, EN 19 / EN 24 / EN 31 flats and plates, 4130 plate, spring-steel stripThickness 6 – 200 mm · flats 20 × 6 to 300 × 100 mmASTM A387, A829; EN 10083-3; BS 970
FittingsButt-weld elbows, tees, reducers and caps in WP5 / WP11 / WP22 / WP91; forged socket-weld & threaded fittings in F11 / F22Butt weld ½" – 24" · Forged ⅛" – 4", Class 3000 / 6000 / 9000ASTM A234, A182, ASME B16.9, B16.11
FlangesWeld neck, slip-on, blind, socket-weld and long weld neck flanges in F5 / F9 / F11 / F22 / F91½" – 24" · Class 150 – 2500ASTM A182, ASME B16.5, B16.47
Round BarBlack (hot-rolled), peeled, bright drawn and ground rounds; forged bars and blocks; hex, square and flat bar – annealed, normalised or hardened & temperedØ 10 – 600 mm · lengths 3 – 6 m · cut pieces and forged blanksASTM A29 / A322 / A434, EN 10083-3, EN 10084, BS 970, IS 1570 Pt 4 / 5, IS 5517
FastenersStud bolts, hex bolts, heavy hex nuts and washers in B7 / B7M / B16 with 2H / 2HM / Gr.4 / Gr.7 nuts; socket-head cap screws Gr. 12.9M10 – M100 · ⅜" – 4" · metric, UNC & 8UNASTM A193 / A194 / A320 L7, ISO 898-1 Gr. 10.9 / 12.9

Supply Conditions

  • Annealed (A)
  • Normalised (N)
  • Hardened & tempered (T / Q&T)
  • Spheroidise annealed (EN 31)
  • Normalised & tempered (F22 Cl.3)
  • Stress relieved

State the required condition and hardness range (e.g. EN 24T, 248–302 HB) on your enquiry.

Bar Finishes & Tolerances

Black
Hot-rolled or forged, as-rolled surface
Peeled / turned
Scale-free, ISO h11 – h12
Bright drawn
ISO h9 – h11, improved straightness
Ground
ISO h6 – h9 for shafts and pins

Testing on Request

UT
Ultrasonic testing of bars and plates to ASTM A388 / EN 10308
Hardness
Brinell / Rockwell survey, Jominy hardenability
Microstructure
Grain size, inclusion rating, decarburisation depth
Standards

Specifications We Supply To

Bars to ASTM, EN, BS and IS; pressure material to ASTM / ASME Section II – supplied to the edition referenced on your purchase order.

ASTM A29 / A322 / A434General requirements, hot-wrought alloy steel bars, and hardened & tempered alloy bars
ASTM A335 / A213Seamless ferritic alloy pipe (P grades) and boiler / superheater tubes (T grades) for high-temperature service
ASTM A182 / A336Forged or rolled alloy steel flanges, fittings, valves and parts (F5, F9, F11, F22, F91)
ASTM A234Wrought carbon and alloy steel butt-weld fittings (WP5, WP11, WP22, WP91)
ASTM A387Chromium-molybdenum alloy steel pressure-vessel plates
ASTM A193 / A194 / A320Alloy bolting for high-temperature (B7, B16) and low-temperature (L7) service with matching nuts
EN 10083-3Steels for quenching and tempering – alloy steels (42CrMo4, 34CrNiMo6, 51CrV4)
EN 10084Case-hardening steels (16MnCr5, 20MnCr5, 20NiCrMo2-2)
EN 10216-2Seamless steel tubes for pressure purposes – alloy steels with elevated-temperature properties
BS 970 (EN series)Legacy British designations EN 19, EN 24, EN 31, EN 36, EN 353 still used on Indian drawings
IS 1570 Pt 4 / Pt 5 · IS 5517Indian Standard alloy constructional steels and steels for hardening & tempering
API Spec 7-1 / NACE MR0175Downhole tool materials (4145H) and sour-service hardness limits (B7M, L7M)

See the full standards directory

Applications

Where Our Alloy Steel Performs

From gearboxes to main-steam lines – supplied to OEMs, forge shops, fastener makers and EPC projects.

Power Plants & Boilers

P11 / P22 / P91 pipe, T-grade tubes, F22 forgings and B16 bolting for main-steam and reheat systems

Refineries & Petrochemical

Cr-Mo piping and A387 plate for hydrogen and high-temperature units; 4130 / 4145H for oil tools

Automotive & Transmission

16MnCr5, 20MnCr5, 8620 and EN 36 bars for gears, shafts and axles

Heavy Engineering

EN 19 / EN 24 bars for shafts, couplings, spindles, press columns and crankshafts

Fastener Manufacturers

EN 19 / 4140 and B7-quality bar for stud bolts, high-tensile bolts and anchor bolts

Pumps, Valves & Compressors

EN 24, 4140 and 17-4 PH-alternative shafts; F11 / F22 valve bodies and bonnets

Plastics & Extrusion Machinery

EN 41B nitriding steel for screws and barrels; EN 31 for wear parts

Mining & Earth-Moving

EN 24, 4340 and EN 47 for pins, bushes, track components and springs

FAQ & Enquiry

Alloy Steel Questions Answered

Send grade, condition, form, size, quantity and testing needs and we quote accurately – usually the same working day.

  1. 1
    Grade & specificatione.g. EN 24 / 817M40, ASTM A335 P22, A182 F11 Cl.2
  2. 2
    ConditionAnnealed, normalised, hardened & tempered – with hardness range
  3. 3
    Product formBar, plate, pipe, tube, fitting, flange or fastener
  4. 4
    SizeDiameter × length, thickness × width × length, NPS + schedule
  5. 5
    QuantityPieces, metres or tonnage
  6. 6
    TestingEN 10204 3.1 / 3.2, UT, hardness, impact, TPI agency
  7. 7
    DeliveryDestination and required date

Frequently Asked Questions

EN 19 or EN 24 – which should I use?

EN 19 (4140) is the economical through-hardening grade for shafts, studs and gears up to about 100 mm section, giving 850–1000 MPa in the T condition. EN 24 (4340) adds nickel, which raises hardenability and toughness so large sections and highly stressed parts reach 1000 MPa or more uniformly. Choose EN 24 for heavy sections, impact loads or when the part will be heat treated after rough machining.

In what condition are alloy steel bars supplied?

Most bars are stocked annealed (soft, for machining) or hardened & tempered (EN 19T, EN 24T, EN 8D-type designations), and case-hardening grades normalised. Tell us the required condition and hardness range; bars can also be supplied peeled, ground or ultrasonically tested for critical shafts.

What is the difference between P11, P22 and P91 pipe?

All are ASTM A335 chromium-molybdenum pipes. P11 (1.25 Cr-0.5 Mo) is used to about 540 °C, P22 (2.25 Cr-1 Mo) to about 580 °C with better resistance to hydrogen attack, and P91 (9 Cr-1 Mo-V-Nb) is a creep-strength-enhanced ferritic steel that permits thinner walls up to about 620 °C. P91 requires strictly controlled welding and post-weld heat treatment.

Case hardening vs through hardening – what is the practical difference?

Through-hardening steels (EN 19, EN 24, EN 31) harden over the full section when quenched, giving uniform strength. Case-hardening steels (EN 36, EN 353, 20MnCr5, 8620) are low in carbon; they are carburised so that only a thin surface layer becomes very hard (58–62 HRC) while the core stays tough. Use case-hardening grades for gears and cams that need a wear-resistant surface with shock resistance.

Can you match a grade from a German, Japanese or Indian drawing?

Yes. Most alloy steels have close equivalents across EN / DIN, AISI / SAE, BS, JIS and IS systems – for example 42CrMo4 = 4140 = EN 19 = SCM440 = 40Cr1Mo28. Our equivalent grades page lists the common cross-references, and material is supplied with certificates showing actual chemistry so you can confirm compliance with the original specification.

Are certificates and third-party inspection available?

All alloy steel is supplied with manufacturer test certificates to EN 10204 3.1 covering chemistry, mechanical properties, heat treatment and hardness. Ultrasonic testing, hardness surveys, impact tests and inspection by Bureau Veritas, DNV, Lloyd's Register, TÜV, EIL or IBR can be arranged on request.

Get in Touch

Need a Material in a Specific Grade or Size?

Send us the product, grade, size, quantity and delivery location – our team replies with stock status and a competitive quote, usually the same working day.