Mon – Sat · 10:00 am – 7:00 pm

Mild Steel

IS 2062 structural plates and sections, IS 1239 / IS 1161 tubes, IS 3589 large-diameter pipe, HR / CR / GI sheets, chequered plate and EN 1A / EN 3 / EN 8 bright bars – the everyday steel for construction, plant structures and fabrication, stocked in Mumbai since 2000.

IS · EN · ASTM Grades All 6 Product Forms MTC EN 10204 3.1
Mild steel structural sections erected at a construction site
PlateIS 2062 E250 · E350 · chequered TubeIS 1239 · IS 1161 · IS 4923 · IS 3589 BarEN 1A · EN 3 · EN 8 bright & black
Overview

Everyday Steel for Structures & Fabrication

Mild steel is low-carbon steel – about 0.05 to 0.25 % carbon – which makes it ductile, easily welded, bent and machined, and the most economical engineering material available. It is bought mainly on strength and dimensions rather than on chemistry, which is why Indian structural standards such as IS 2062 and IS 1239 dominate the trade.

We stock mild steel in all six of our product forms: plates and sheets, ERW and structural tubes, hollow sections, flanges and fittings, black and bright bars, and commercial fasteners. Where a drawing calls for a European or American grade – S235JR, ST 37, A36 – we supply the direct equivalent with certificates. For pressure-rated ASTM material see our carbon steel page.

  • IS 2062 E250 / E350 plates from 6 to 150 mm, cut to size
  • IS 1239 galvanised & black tubes with matching fittings
  • Bright bars EN 1A / EN 3 / EN 8 for turned components
  • Bulk stock for prompt delivery to sites and fabricators

Quick Facts

Carbon
0.05 – 0.25 % (EN 8 up to 0.44 %)
Core grades
IS 2062 E250 / E350, IS 1239, IS 1161, IS 4923, EN 1A / EN 3 / EN 8, S235JR / S355JR
Strength
YS 250 – 450 MPa · UTS 410 – 570 MPa
Density
7.85 g/cm³
Forms
Plate, sheet, coil, tube, hollow section, bar, flat, angle, channel, fasteners
Certification
EN 10204 3.1 mill certificates; NABL lab testing on request

Mild Steel vs Carbon Steel – Which Do You Need?

The two terms overlap in metallurgy but mean different things when you buy. Ordering the right one avoids paying for pressure certification you do not need – or installing structural steel where a pressure grade is mandatory.

 Mild Steel (structural)Carbon Steel (pressure grade)
Typical standardsIS 2062, IS 1239, IS 1161, EN 10025, A36ASTM A106, A53, A105, A234, A516, A333
Carbon content≈ 0.05 – 0.25 %Low to medium, tightly controlled per grade
Bought onYield strength, dimensions, impact gradeFull chemistry, heat treatment, per-heat testing, traceability
Heat treatmentAs rolled (normalised for some grades)Normalised, Q&T or hot-finished as specified
Typical useStructures, platforms, utility water / air lines, fabricationSteam, oil & gas, boilers, pressure vessels, process piping
CertificationMill TC (EN 10204 3.1)EN 10204 3.1 / 3.2, IBR, TPI, NACE as required
Grades

Mild Steel Grades & Standards We Stock

Indian Standard grades with their common international equivalents. Values are typical of the current standards; the edition on your purchase order governs.

Swipe sideways to see all columns.

Grade / StandardEquivalentKey Composition (wt %)PropertiesTypical Use
IS 2062 E250 A / BR / B0 / CFe 410 WA / WB / WC (old)
≈ S235JR / S275JR
C ≤ 0.23 (A) / 0.22 (B) / 0.20 (C) · Mn ≤ 1.50YS ≥ 250 MPa · UTS ≥ 410 MPa · elongation ≥ 23 %; BR impact tested at room temp., B0 at 0 °C, C at −20 °CGeneral structural plates, sections, flats and bars for buildings, sheds, platforms and fabrication
IS 2062 E350 BR / B0 / CFe 490 (old) ≈ S355JR / J0 / J2C ≤ 0.20 · Mn ≤ 1.55 · micro-alloyedYS ≥ 350 MPa · UTS ≥ 490 MPa; weldable high-strength structural steelCranes, heavy structures, earth-moving equipment, transmission towers
IS 2062 E410 / E450Fe 540 / Fe 570 (old)C ≤ 0.20 · Mn ≤ 1.60 · Nb / V / TiYS ≥ 410 / 450 MPa high-strength structural gradesBridges, booms, chassis, high-rise structures
IS 1239 Part 1 (Light / Medium / Heavy)Yst 210 (≈ A53 Gr.A for general use)C ≤ 0.20 · Mn ≤ 1.30 (typical)ERW steel tubes 15 – 150 NB; UTS ≥ 320 MPa; black or galvanised (IS 4736)Water, gas and air lines, fire-fighting, scaffolding, fencing, handrails
IS 1161 Yst 210 / 240 / 310—C ≤ 0.20 / 0.25 · Mn ≤ 1.30Steel tubes for structural purposes, YS 210 / 240 / 310 MPaTrusses, columns, space frames, bus bodies, conveyor gantries
IS 3589 Fe 330 / Fe 410≈ A53 / API 5L Gr.A / B for utility linesC ≤ 0.20–0.25ERW / SAW pipes 168.3 – 2540 mm OD for water, gas and sewageWater supply, penstocks, piling, casing, large-diameter utility lines
IS 4923 Yst 210 / 240 / 310—C ≤ 0.20 · Mn ≤ 1.30Hollow steel sections (square & rectangular) for structural useBuilding frames, pre-engineered buildings, furniture, machine frames
IS 1079 HR / IS 513 CR (CR1 – CR5, DD, EDD)HR: ≈ A1011 · CR: ≈ A1008 / DC01 – DC04C ≤ 0.12 – 0.15 · Mn ≤ 0.60Hot-rolled and cold-rolled low-carbon sheet and coil in commercial, drawing and extra-deep-drawing qualitiesPanels, cabinets, ducting, pressed and drawn parts, auto components
IS 277 GI / GP sheetASTM A653 (equivalent coating classes)Low-carbon base, zinc coating 120 – 275 g/m²Hot-dip galvanised plain and corrugated sheetRoofing, cladding, ducting, cable trays, enclosures
IS 3502 chequered plate—As IS 2062 E250Hot-rolled floor plate with raised tear-drop / diamond pattern, 3 – 12 mmWalkways, platforms, stair treads, truck beds
EN 1A (230M07) / EN 1A LeadedSAE 1213 / 12L14 · 11SMn30 / 11SMnPb30C ≤ 0.15 · S 0.20–0.30 · Mn 0.90–1.30 (+ Pb)Free-cutting mild steel for high-speed automatic machining; not weldableTurned parts, studs, pins, bushes, fittings
EN 3 (070M20) / EN 3BSAE 1020 · C22C 0.15–0.25 · Mn 0.50–0.90General-purpose low-carbon bright bar; weldable, case-hardenableShafts, spacers, brackets, lightly stressed machine parts
EN 8 (080M40)SAE 1040 / 1045 · C40 / C45C 0.36–0.44 · Mn 0.60–1.00Medium-carbon bar; UTS 550–700 MPa normalised; flame / induction hardenableAxles, shafts, gears, studs, bolts, keys
S235JR / S275JR / S355JR (EN 10025-2)formerly ST 37-2 / ST 44-2 / ST 52-3 (DIN 17100)C ≤ 0.17 – 0.24 · Mn ≤ 1.40 – 1.60European structural steels, YS 235 / 275 / 355 MPa; JR = 27 J at +20 °C, J2 = −20 °CExport fabrications, imported machinery spares, EPC projects to European codes
Forms We Supply

Mild Steel in All Six Product Forms

Plates, tubes, sections and bars are held in bulk; cutting, drilling and galvanising are arranged to your drawing.

Swipe sideways to see all columns.

ProductTypes AvailableSize RangeStandards
Pipes & TubesERW black & galvanised tubes (light / medium / heavy), structural tubes, square & rectangular hollow sections, large-diameter ERW / SAW pipe15 – 150 NB (IS 1239) · hollow sections 20 × 20 to 400 × 400 mm · pipe up to 2540 mm ODIS 1239 Pt 1, IS 1161, IS 4923, IS 3589, IS 4736 (galvanising)
Sheets & PlatesHR plate & sheet, CR sheet & coil, GI / GP plain and corrugated sheet, chequered plate, cut-to-size profilesSheet 0.4 – 6 mm · plate 6 – 150 mm · widths up to 2500 mmIS 2062, IS 1079, IS 513, IS 277, IS 3502, EN 10025
FittingsGalvanised & black malleable-iron threaded fittings, ERW socket-weld and butt-weld fittings, pipe nipples, bends⅛" – 6" threaded · ½" – 24" butt weldIS 1879, IS 1239 Pt 2, ASME B16.9 (CS)
FlangesPlate (slip-on) flanges, blind flanges, screwed flanges, table / PN flanges, IS flanges½" – 24" · PN 6 – PN 40 · Table D / E / FIS 6392, BS 10, EN 1092-1, ASME B16.5 (CS)
Round BarHot-rolled black rounds, bright drawn rounds, hex and square bar, flats and anglesØ 6 – 300 mm · flats 20 × 3 to 300 × 50 mm · lengths 6 mIS 2062, IS 1570 Pt 2, EN 10277 (bright), BS 970
FastenersHex bolts and nuts, machine screws, washers, foundation bolts, threaded rods – plain, zinc-plated or hot-dip galvanisedM4 – M48 · Class 4.6 / 4.8 / 5.6 / 8.8IS 1363, IS 1364, IS 1367, ISO 898-1, DIN 931 / 933 / 934

Also Available

  • Angles
  • Channels
  • I-beams / joists
  • Flats
  • Squares
  • Hex bar
  • Circles & rings
  • Perforated sheet
  • Wire mesh

Structural sections to IS 808 / IS 2062, supplied with plates against the same order.

Surface Options

Black
Mill scale or mill-varnished tube
Galvanised
Hot-dip to IS 4736 / IS 2629; pre-galvanised GP sheet
Primed
Shot-blasted and primer-coated plate on request

Processing & Delivery

Cutting
Gas / plasma profiling, shearing, saw cutting to length
Threading
BSP threading and socketing of IS 1239 tubes
Delivery
Bulk stock for quick dispatch within Mumbai and across India
Standards

Specifications We Supply To

Indian Standards first, with the European and American equivalents most often quoted on drawings.

IS 2062Hot-rolled medium and high-tensile structural steel – plates, sections, flats and bars (E250 to E650)
IS 1239 Part 1 / Part 2Mild steel tubes for water, gas and air (light, medium, heavy) and tubulars / fittings
IS 1161 / IS 4923Steel tubes and hollow steel sections for structural purposes
IS 3589Electrically welded steel pipes for water, gas and sewage (168.3 – 2540 mm OD)
IS 1079 / IS 513Hot-rolled and cold-rolled low-carbon steel sheet and strip
IS 277Galvanised steel sheets (plain and corrugated)
IS 3502Steel chequered plates
IS 4736Hot-dip zinc coating on mild steel tubes
IS 1363 / IS 1364 / IS 1367Hexagon head bolts, screws and nuts; technical supply conditions for threaded fasteners
EN 10025-2Hot-rolled non-alloy structural steels S235 / S275 / S355
EN 10277 / BS 970Bright steel products – EN 1A, EN 3, EN 8 designations
ASTM A36 / A53US structural plate and general-service pipe commonly accepted in place of IS grades

See the full standards directory

Applications

Where Our Mild Steel Is Used

Supplied to builders, fabricators, plant maintenance teams and OEMs – from single plates to project tonnage.

Construction & Infrastructure

IS 2062 plates, angles, channels and hollow sections for buildings, sheds and bridges

Fabrication & Job Work

Cut-to-size plates, flats, tubes and chequered plate for fabricators and job shops

Plant Structures & Platforms

Pipe racks, walkways, handrails, stair treads and cable-tray supports for chemical, sugar and cement plants

Water & Fire-Fighting Lines

IS 1239 galvanised and black tubes with fittings and flanges for water, air and sprinkler systems

Automotive & Transport

CR / EDD sheet for pressings, EN 8 shafts, hollow sections for bus and truck bodies

Pre-Engineered Buildings

E350 plates for built-up sections, Z / C purlins from GP coil, roofing sheet

General Engineering

EN 1A, EN 3 and EN 8 bright bars for turned and machined components

Agriculture & Material Handling

Conveyor structures, hoppers, silos, trailers and farm equipment

FAQ & Enquiry

Mild Steel Questions Answered

Send grade, form, size, quantity and finish and we quote accurately – usually the same working day.

  1. 1
    Grade & standarde.g. IS 2062 E250 BR, IS 1239 medium class
  2. 2
    Product formPlate, sheet, tube, section, bar, flange or fastener
  3. 3
    SizeThickness × width × length, NB × class, or section size
  4. 4
    FinishBlack, galvanised, primed, bright
  5. 5
    QuantityPieces, metres or tonnage
  6. 6
    CertificationMill TC, lab test report, third-party inspection
  7. 7
    DeliverySite address and required date

Frequently Asked Questions

What exactly is mild steel?

Mild steel is low-carbon steel – roughly 0.05 to 0.25 % carbon – that is soft, ductile, easy to weld, bend and machine, and cannot be hardened significantly by heat treatment. In India it is normally bought to IS 2062 (structural) or IS 1239 (tubes); internationally the equivalents are S235JR / S275JR, A36 and 1018 / 1020.

Mild steel vs carbon steel – is there a real difference?

Commercially, yes. "Mild steel" means structural-grade material sold mainly on strength (IS 2062, IS 1239). "Carbon steel" in the piping trade means pressure-rated material to ASTM / ASME specifications (A106, A105, A516) with tighter chemistry, mandatory heat treatment and per-heat testing. Use pressure-grade carbon steel for boilers, pressure piping and vessels; mild steel is right for structures, platforms, utility lines and general fabrication.

What is the difference between IS 2062 E250 A, BR, B0 and C?

All four have the same minimum yield strength of 250 MPa. The suffix sets the impact-test requirement: A – no impact test; BR – 27 J at room temperature; B0 – 27 J at 0 °C; C – 27 J at −20 °C (and lower carbon). Specify BR or B0 for welded structures and C for low-temperature or dynamically loaded work.

Light, medium or heavy class IS 1239 tube – how do I choose?

The classes differ only in wall thickness for the same nominal bore – for example 50 NB is 2.9 mm (light), 3.6 mm (medium) and 4.5 mm (heavy). Light class suits low-pressure water and fencing, medium is the usual choice for building services and fire lines, and heavy class is used where threading, higher pressure or corrosion allowance is needed.

Do you supply test certificates for mild steel?

Yes. Plates, tubes and bars are supplied with manufacturer test certificates (EN 10204 3.1) showing heat number, chemistry and mechanical properties. Material can also be tested at NABL-accredited laboratories or inspected by a third-party agency on request.

Get in Touch

Need a Material in a Specific Grade or Size?

Send us the product, grade, size, quantity and delivery location – our team replies with stock status and a competitive quote, usually the same working day.