Mon – Sat · 10:00 am – 7:00 pm

Material Grades

A technical reference to the grades Honesty Impex stocks and supplies – equivalents, nominal composition, key properties and typical applications across stainless steel, carbon steel, mild steel, alloy steel, tool & die steel, high speed steel and non-ferrous metals.

7 Material Families 100+ Grades UNS · W.Nr. · AISI · BS · IS

Search by grade, UNS, W.Nr., AISI, IS or application.

Compositions are nominal values (weight %) and properties are typical, for guidance only. Exact limits depend on the product standard, form and condition – always refer to the applicable specification and the mill test certificate supplied with the material.

01SS

Stainless Steel

Iron-chromium alloys with at least 10.5% chromium, which forms a self-healing passive oxide film. Austenitic 200 and 300 series grades offer excellent formability and weldability; martensitic grades (410, 420, 431) can be hardened; ferritic 430 is magnetic and economical; duplex grades combine austenite and ferrite for roughly twice the yield strength of 316 and superior chloride stress-corrosion resistance. Our largest stock family – including PVC-coated 304 and 316 sheet. See the Stainless Steel page for forms and sizes.

Forms: Sheets, plates, coils, seamless & welded pipes and tubes, round bars, flats, fittings, flanges, fasteners, wire

Standards: ASTM A240, A312, A213, A269, A276, A479, A182, A403, A790 · EN 10088 · IS 6911 · JIS G4303 / G4304

GradeEquivalentsNominal CompositionKey PropertiesTypical Applications
SS 202 Austenitic · Cr-Mn-NiUNS S20200 · W.Nr. 1.4373 · SUS 202Cr 18 · Mn 8.5 · Ni 5 · N ≤0.25 · C ≤0.15Low-nickel austenitic grade with manganese and nitrogen replacing part of the nickel; good strength and formability at lower cost than 304; moderate corrosion resistance.Utensils, railings and architectural work, automotive trim, storage tanks, indoor applications
SS 304 / 304L AusteniticUNS S30400 / S30403 · W.Nr. 1.4301 / 1.4307 · SUS 304 · IS X04Cr19Ni9Cr 18 · Ni 8 · C ≤0.07 (304L ≤0.03)General-purpose "18/8" stainless; excellent formability and weldability; non-magnetic when annealed. 304L avoids sensitisation after welding. Available PVC-coated for scratch-free fabrication.Food & dairy equipment, kitchenware, chemical tanks, architectural work, heat exchangers
SS 316 / 316L AusteniticUNS S31600 / S31603 · W.Nr. 1.4401 / 1.4404 · SUS 316 · IS X04Cr17Ni12Mo2Cr 17 · Ni 12 · Mo 2.5 · C ≤0.08 (316L ≤0.03)Molybdenum improves pitting and crevice resistance in chlorides (PREN ≈ 24); good creep strength. Our PVC-coated 316 sheet speciality grade.Marine fittings, pharmaceutical & chemical plants, pulp & paper, coastal structures
SS 316Ti Austenitic · Ti-stabilisedUNS S31635 · W.Nr. 1.4571 · SUS 316TiCr 17 · Ni 12 · Mo 2.2 · Ti ≥5×CTitanium-stabilised 316 that resists intergranular corrosion after welding or service at 425–815 °C; widely specified on European drawings.Chemical and process equipment, exhaust systems, welded pressure vessels, heat exchangers
SS 321 Austenitic · Ti-stabilisedUNS S32100 · W.Nr. 1.4541 · SUS 321Cr 18 · Ni 10 · Ti ≥5×CTitanium-stabilised 304 for service in the 425–815 °C sensitisation range; good oxidation resistance and creep strength.Aircraft exhaust manifolds, expansion joints, boiler casings, high-temperature chemical equipment
SS 347 Austenitic · Nb-stabilisedUNS S34700 · W.Nr. 1.4550 · SUS 347Cr 18 · Ni 11 · Nb ≥10×CNiobium-stabilised alternative to 321 with slightly better high-temperature strength and weld properties.Refinery heaters, high-temperature piping, welded chemical plant, aerospace components
SS 309 / 309S Austenitic · Heat-resistingUNS S30900 / S30908 · W.Nr. 1.4828 / 1.4833Cr 23 · Ni 13 · C ≤0.20 (309S ≤0.08)Good oxidation resistance up to about 1000 °C; high-alloy filler for dissimilar welds.Furnace and boiler components, heat exchangers, dissimilar-metal welding
SS 310 / 310S Austenitic · Heat-resistingUNS S31000 / S31008 · W.Nr. 1.4845 · SUS 310SCr 25 · Ni 20 · C ≤0.25 (310S ≤0.08)Heat-resisting grade with excellent oxidation resistance up to about 1100 °C.Furnace parts, heat-treatment fixtures, radiant tubes, kiln and burner components
SS 410 MartensiticUNS S41000 · W.Nr. 1.4006 · SUS 410Cr 12.5 · C ≤0.15Hardenable by heat treatment; magnetic; good strength with moderate corrosion resistance.Valve trim, pump shafts, turbine parts, fasteners, cutlery
SS 420 MartensiticUNS S42000 · W.Nr. 1.4021 / 1.4028 · SUS 420J1/J2Cr 13 · C ≥0.15Higher carbon for greater hardness (around 50 HRC when hardened); good wear resistance.Surgical and dental instruments, cutlery, moulds, pump shafts
SS 430 FerriticUNS S43000 · W.Nr. 1.4016 · SUS 430Cr 17 · C ≤0.12Magnetic, non-hardenable; good formability and resistance to mild corrosion; economical.Appliance panels, automotive trim, sinks, decorative applications
SS 431 Martensitic · Ni-bearingUNS S43100 · W.Nr. 1.4057 · SUS 431Cr 16 · Ni 2 · C 0.20Highest corrosion resistance of the martensitic grades and high tensile strength after hardening and tempering (about 850–1000 MPa).Pump and propeller shafts, marine fasteners, valve parts, aircraft fittings
SS 904L Super austeniticUNS N08904 · W.Nr. 1.4539Cr 20 · Ni 25 · Mo 4.5 · Cu 1.5 · C ≤0.02High-alloy austenitic grade with excellent resistance to sulphuric and phosphoric acids and to chloride pitting (PREN ≈ 35); non-magnetic.Sulphuric-acid plants, fertiliser and phosphoric-acid equipment, seawater systems, pharmaceutical reactors
Duplex 2205 DuplexUNS S31803 / S32205 · W.Nr. 1.4462Cr 22 · Ni 5 · Mo 3 · N 0.17About twice the yield strength of 316; excellent chloride stress-corrosion cracking resistance (PREN ≈ 35).Oil & gas, chemical tankers, desalination, pulp & paper, heat exchangers
Super Duplex 2507 Super DuplexUNS S32750 · W.Nr. 1.4410Cr 25 · Ni 7 · Mo 4 · N 0.27Very high strength; outstanding pitting and crevice resistance in seawater (PREN ≥ 40).Offshore platforms, subsea systems, seawater cooling, firewater lines

Also stocked on request: SS 303 (free-machining), SS 317L, SS 409, SS 416 and SS 440C. PVC / plastic-coated sheets in 304 and 316 are a Honesty Impex speciality.

02CS

Carbon Steel

Plain carbon steels for pressure piping, boilers, vessels and forged piping components – specified by ASTM / ASME for guaranteed chemistry, strength and (where required) impact toughness. Also medium-carbon engineering grades for shafts and machined parts. See the Carbon Steel page.

Forms: Seamless & ERW pipes, boiler tubes, BQ plates, forged flanges & fittings, butt-weld fittings, round bars, fasteners

Standards: ASTM / ASME A106, A53, A333, A210, A516, A105, A350, A234, A420, A36 · SAE J403

GradeEquivalentsNominal CompositionKey PropertiesTypical Applications
A106 Gr. B Seamless pipe · High temp.ASTM A106 / ASME SA106 Gr. B · UNS K03006 · P265GH (similar)C ≤0.30 · Mn 0.29–1.06 · Si ≥0.10The standard seamless carbon steel pipe for high-temperature service; tensile ≥415 MPa, yield ≥240 MPa; weldable and bendable.Refinery and power-plant piping, steam lines, boilers, process piping, hydraulic lines
A53 Gr. B ERW / seamless pipeASTM A53 Gr. B · UNS K03005 · IS 1239 (similar)C ≤0.30 · Mn ≤1.20General-purpose black or hot-dip galvanised pipe; tensile ≥415 MPa, yield ≥240 MPa; threaded, grooved or plain ends.Water, air and gas lines, fire-fighting systems, structural and mechanical use, low-pressure steam
A333 Gr. 6 Low-temperature pipeASTM A333 / ASME SA333 Gr. 6 · UNS K03006C ≤0.30 · Mn 0.29–1.06 · Si ≥0.10Normalised seamless pipe impact tested at −46 °C; tensile ≥415 MPa, yield ≥240 MPa.LPG and cryogenic piping, cold-climate pipelines, refrigeration plants
A105 / A105N ForgingASTM A105 / ASME SA105 · UNS K03504 · C22.8 (1.0460, similar)C ≤0.35 · Mn 0.60–1.05 · Si 0.10–0.35The standard carbon steel for forged flanges and socket-weld / threaded fittings; tensile ≥485 MPa, yield ≥250 MPa; A105N normalised for improved toughness.Flanges, forged fittings, olets, valve bodies, piping components
A234 WPB Butt-weld fittingASTM A234 / ASME SA234 WPB · UNS K03006C ≤0.30 · Mn 0.29–1.06 · Si ≥0.10Wrought carbon steel fittings matching A106 Gr. B / A53 Gr. B pipe; tensile 415–585 MPa, yield ≥240 MPa.Elbows, tees, reducers, caps and stub ends for moderate and high-temperature piping
A350 LF2 Low-temperature forgingASTM A350 / ASME SA350 LF2 Cl. 1 · UNS K03011C ≤0.30 · Mn 0.60–1.35 · Si 0.15–0.30Carbon steel forgings impact-tested at −46 °C; tensile 485–655 MPa, yield ≥250 MPa; often dual-certified with A105.Low-temperature flanges, fittings and valves for LPG, petrochemical and cold climates
A420 WPL6 Low-temperature fittingASTM A420 / ASME SA420 WPL6 · UNS K03006C ≤0.30 · Mn 0.50–1.35 · Si 0.15–0.40Butt-weld fittings impact tested at −46 °C, matching A333 Gr. 6 pipe and A350 LF2 flanges.Low-temperature process and refrigeration piping, LPG terminals
SA 516 Gr. 60 / 70 Boiler quality (BQ) plateASTM A516 / ASME SA516 · UNS K02100 / K02700 · IS 2002 Gr. 2 (similar)C ≤0.27–0.31 (by thickness) · Mn 0.85–1.20 · Si 0.15–0.40Carbon steel plate for moderate and lower-temperature pressure service; Gr. 70 tensile 485–620 MPa, yield ≥260 MPa; HIC / normalised options.Boilers, pressure vessels, storage tanks, heat exchangers, columns
SA 210 Gr. A1 / C Boiler tubeASTM A210 / ASME SA210 · UNS K02707 / K03501 · BS 3059 360/440C ≤0.27 (A1) / ≤0.35 (C) · Mn ≤0.93 / 0.29–1.06Seamless medium-carbon boiler and superheater tubes; tensile ≥415 MPa (A1), ≥485 MPa (C).Water-wall, economiser and boiler tubes, heat exchangers
A36 StructuralASTM A36 · UNS K02600 · S275JR / IS 2062 E250 (similar)C ≤0.26 · Mn 0.80–1.20 · Si ≤0.40Carbon structural steel with yield ≥250 MPa and tensile 400–550 MPa; readily welded, bolted and riveted.Structural plates and sections, base plates, brackets, general fabrication
AISI 1018 / 1020 Low carbon barSAE 1018 / 1020 · C15 / C22 (1.0401 / 1.0402) · EN 3B (similar)C 0.18–0.20 · Mn 0.60–0.90Low-carbon steel with good weldability and machinability; can be carburised for a hard case.Shafts, pins, spacers, brackets, machined and fabricated parts
C45 / AISI 1045 Medium carbon barW.Nr. 1.0503 · SAE 1045 · EN 8 / 080M46 · IS 45C8 · S45CC 0.45 · Mn 0.65 · Si 0.25Medium-carbon steel with tensile about 600–750 MPa normalised; induction or flame hardenable to 55 HRC at the surface.Shafts, gears, bolts, crankshafts, hydraulic rods, machine parts

Cr-Mo pressure grades (A335 P11 / P22 / P91, A182 F11 / F22, A387 plates) are listed under Alloy Steel. Structural mild steel grades to IS 2062 are under Mild Steel.

03MS

Mild Steel

Low-carbon structural and general-engineering steels – the most widely used and economical steels for fabrication, construction and machining. Supplied to Indian (IS), European (EN / DIN) and British (BS 970 "EN" series) standards. See the Mild Steel page.

Forms: HR / CR sheets and plates, chequered plates, ERW pipes and tubes, round and bright bars, flats, angles, channels, fasteners

Standards: IS 2062, IS 1079, IS 513, IS 1239, IS 1161, IS 3589, IS 9550 · BS 970 · EN 10025 · EN 10087

GradeEquivalentsNominal CompositionKey PropertiesTypical Applications
IS 2062 E250 Structural · Gr. A / B / BR / B0IS 2062:2011 E250 (formerly Fe 410) · S235JR / S275JR (similar) · ASTM A36 (similar)C ≤0.22 · Mn ≤1.50 · Si ≤0.40 · S, P ≤0.045Standard Indian structural steel; yield ≥250 MPa, tensile ≥410 MPa, elongation ≥23%; excellent weldability. Quality B / BR / B0 add impact requirements.Building and bridge structures, plates, angles, channels, beams, general fabrication
IS 2062 E350 High-tensile structuralIS 2062 E350 (formerly Fe 490) · S355JR / S355J0 (similar)C ≤0.20 · Mn ≤1.55 · Si ≤0.45 · micro-alloyedHigher strength for lighter sections; yield ≥350 MPa, tensile ≥490 MPa; good weldability with micro-alloy chemistry.Cranes, heavy structures, earth-moving equipment, transmission towers, wagons
IS 1239 (Part 1) MS tubes · Light / Medium / HeavyIS 1239 Pt 1 · YSt 210 / 240 / 310 · BS 1387 (similar)C ≤0.20 · Mn ≤1.30 (ERW)Electric-resistance-welded black or galvanised tubes, ½" to 6" NB, in light (A), medium (B) and heavy (C) classes; threaded or plain ends.Water and gas lines, fire-fighting, scaffolding, fencing, structural and general-purpose piping
IS 1161 Structural tubesIS 1161 YSt 210 / 240 / 310 · EN 10219 S235 / S275 / S355 (similar)C ≤0.20–0.25 · Mn ≤1.30–1.50Hot-finished or ERW steel tubes for structural purposes with specified yield strength (210, 240 or 310 MPa).Trusses, columns, towers, scaffolding, handrails, structural frames
IS 3589 Fe 330 / Fe 410 Large-diameter welded pipeIS 3589 · API 5L Gr. A / B (similar)C ≤0.20–0.25 · Mn ≤1.20Electric-fusion or spiral-welded pipe from 168 mm to 2540 mm OD for water, sewage and low-pressure gas.Water supply and sewage mains, penstocks, casing, structural piles
EN 1A / EN 1A Leaded Free-cuttingBS 970 230M07 / 230M07Pb · 11SMn30 / 11SMnPb30 (1.0715 / 1.0718) · AISI 1213 / 12L14C ≤0.10 · Mn 1.1 · S 0.30 (Pb 0.25 in leaded)Sulphur (and lead) additions for very high machining speeds and excellent surface finish; not for welding or heat treatment.Precision turned parts, bushes, studs, hydraulic fittings, screw-machine components
EN 3B Bright mild steelBS 970 070M20 · C22 (1.0402) · AISI 1020 · IS 9550 20C8 (similar)C 0.20 · Mn 0.7Low-carbon bright-drawn bar with good weldability and machinability; can be case-hardened.General engineering, shafts, pins, brackets, dowels, fabricated parts
EN 8 / EN 8D Medium carbonBS 970 080M40 · C40 (1.0511) · AISI 1040 · IS 40C8 · S40CC 0.40 · Mn 0.8Unalloyed medium-carbon steel, tensile about 550 MPa min. normalised; can be induction or flame hardened. EN 8D is the bright-drawn version.Shafts, studs, bolts, axles, gears, keys, general engineering
ST 37 / S235JR StructuralDIN St 37-2 · EN 10025 S235JR (1.0038) · IS 2062 E250 (similar)C ≤0.17 · Mn ≤1.40European general structural steel with yield ≥235 MPa and tensile 360–510 MPa; good weldability and formability.Structural sections, plates, tubes, welded frames, general fabrication
ST 52.3 / S355J2 High-strength structuralDIN St 52-3 · EN 10025 S355J2 (1.0577) · IS 2062 E350 (similar)C ≤0.20 · Mn ≤1.60 · Si ≤0.55Structural steel with yield ≥355 MPa and impact toughness at −20 °C; good weldability; also as hydraulic cylinder tube (E355).Cranes, bridges, earth-moving equipment, hydraulic cylinder tubes, heavy fabrication
IS 1079 / IS 513 HR / CR sheetIS 1079 HR1–HR4 (hot rolled) · IS 513 CR1–CR5 (cold rolled) · DC01–DC04 (similar)C ≤0.10–0.15 · Mn ≤0.50–0.60Low-carbon sheet and strip in drawing and deep-drawing qualities; smooth CR surface suitable for painting and plating.Panels, enclosures, pressings, automotive and appliance components, ducting

MS chequered plates, angles, channels, beams and flats are supplied to IS 2062 E250; bright bars to IS 9550. Galvanised sheets and pipes are available on request.

04AS

Alloy Steel

Steels alloyed with chromium, nickel, molybdenum and manganese for strength, toughness and high-temperature performance. Through-hardening grades (EN 19, EN 24) are used hardened and tempered; case-hardening grades (20MnCr5, EN 353, 8620) are carburised for a hard surface over a tough core; Cr-Mo grades (P11, P22, P91) resist creep in steam and refinery service. See the Alloy Steel page.

Forms: Round, hex and square bars, forged rounds, blocks, seamless pipes and tubes, plates, forged flanges & fittings, butt-weld fittings, fasteners

Standards: BS 970 (EN series) · EN 10083, 10084, 10085 · SAE J404 · IS 1570, IS 5517 · ASTM A335, A213, A182, A234, A387, A193

GradeEquivalentsNominal CompositionKey PropertiesTypical Applications
EN 19 / 4140 Cr-Mo, through-hardeningBS 970 709M40 · 42CrMo4 (1.7225) · AISI 4140 · IS 40Cr1Mo28 · SCM 440C 0.40 · Cr 1.05 · Mo 0.25 · Mn 0.8High tensile strength with good toughness and fatigue resistance; commonly supplied in T condition (850–1000 MPa) or annealed.Shafts, gears, spindles, oil & gas tools, high-tensile bolts (B7 studs), hydraulic rods
EN 24 / 4340 Ni-Cr-Mo, through-hardeningBS 970 817M40 · 34CrNiMo6 (1.6582, similar) · AISI 4340 · IS 40Ni2Cr1Mo28 · SNCM 439C 0.40 · Ni 1.5 · Cr 1.2 · Mo 0.27Very high tensile strength and toughness in large sections; hardened & tempered up to about 1300 MPa; good hardenability.Heavy-duty shafts, crankshafts, connecting rods, gears, axles, aerospace and defence parts
EN 31 / 52100 Bearing steelBS 970 535A99 · 100Cr6 (1.3505) · AISI 52100 · IS 103Cr1 · SUJ 2C 1.0 · Cr 1.4 · Mn 0.35High-carbon chromium steel hardening to about 60–64 HRC; excellent wear and rolling-contact fatigue resistance.Ball and roller bearings, bearing races, gauges, punches, rollers, bushes
EN 36 / EN 36C Ni-Cr, case-hardeningBS 970 655M13 / 832M13 · 14NiCr14 (1.5752) · AISI 3310 (similar) · SNC 815C 0.13 · Ni 3.4 · Cr 0.85High-nickel carburising steel giving a very tough core under a hard case; retains toughness in large sections.Heavy-duty gears, camshafts, crown wheels, pinions, aircraft and truck transmission parts
EN 353 Ni-Cr-Mo, case-hardeningBS 970 815M17 · 17NiCrMo6-4 (1.6566, similar) · IS 15Ni4Cr1 (similar)C 0.17 · Ni 1.45 · Cr 1.0 · Mo 0.15Carburising steel with high core strength and good hardenability; widely used in Indian gear manufacture.Gears, pinions, shafts, cams, heavy-duty transmission parts
SAE 8620 Ni-Cr-Mo, case-hardeningAISI 8620 · 20NiCrMo2-2 (1.6523) · BS 805M20 (EN 362) · SNCM 220C 0.20 · Ni 0.55 · Cr 0.5 · Mo 0.2Versatile carburising steel with a tough core and hard, wear-resistant case; good machinability.Gears, ring gears, camshafts, king pins, chain components, fasteners
16MnCr5 Mn-Cr, case-hardeningW.Nr. 1.7131 · SAE 5115 · IS 16Mn5Cr4 · SCr 415C 0.16 · Mn 1.15 · Cr 0.95Case-hardening steel with good machinability and surface hardness after carburising.Small and medium gears, piston pins, shafts, cams
20MnCr5 Mn-Cr, case-hardeningW.Nr. 1.7147 · SAE 5120 · IS 20Mn5Cr4 · SCr 420C 0.20 · Mn 1.25 · Cr 1.15Higher hardenability than 16MnCr5 for larger sections; high core strength.Automotive and industrial gears, crown wheels, shafts, spindles
SAE 4130 Cr-Mo, through-hardeningAISI 4130 · 25CrMo4 (1.7218) · 30CrMo4 · SCM 430C 0.30 · Cr 0.95 · Mo 0.2Lower carbon than 4140 for better weldability while keeping good strength and toughness after H&T; also as seamless tube.Oil-tool components, aircraft tubing and structures, pressure vessels, welded frames
EN 41B Cr-Al-Mo, nitridingBS 970 905M39 · 41CrAlMo7-10 (1.8509) · SACM 645C 0.39 · Cr 1.6 · Al 1.1 · Mo 0.2Nitriding steel developing a very hard, wear-resistant surface (about 900–1100 HV) with minimal distortion.Nitrided shafts, spindles, extruder screws and barrels, cams, liners
EN 47 Cr-V, spring steelBS 970 735A51 · 51CrV4 (1.8159) · AISI 6150 · IS 50Cr4V2 · SUP 10C 0.50 · Cr 0.95 · Mn 0.8 · V ≥0.15Spring steel with high fatigue strength and toughness after hardening & tempering.Leaf and coil springs, torsion bars, highly stressed gears and shafts
A335 P11 / A213 T11 1¼Cr-½Mo · Pipe & tubeASTM A335 P11 · UNS K11597 · 13CrMo4-5 (1.7335) · STPA 23Cr 1.25 · Mo 0.5 · C ≤0.15 · Si 0.5–1.0Creep-resisting Cr-Mo steel for service up to about 550 °C; good weldability with preheat; tensile ≥415 MPa.Superheater and reheater tubes, refinery furnace tubes, steam headers and piping
A335 P22 / A213 T22 2¼Cr-1Mo · Pipe & tubeASTM A335 P22 · UNS K21590 · 10CrMo9-10 (1.7380) · STPA 24Cr 2.25 · Mo 1.0 · C ≤0.15Higher Cr-Mo content for creep strength to about 580 °C and resistance to hydrogen attack; tensile ≥415 MPa.High-pressure steam lines, hydrocrackers, reformer piping, boiler tubes
A335 P91 / A213 T91 9Cr-1Mo-V · Pipe & tubeASTM A335 P91 · UNS K90901 · X10CrMoVNb9-1 (1.4903) · STPA 28Cr 9 · Mo 1 · V 0.2 · Nb 0.08 · N 0.05Creep-strength-enhanced ferritic steel for high-pressure, high-temperature steam up to about 600 °C; needs controlled heat treatment and welding.Supercritical boiler tubes and headers, main steam piping, high-temperature refinery lines
A182 F11 / F22 / F5 Cr-Mo forgingsASTM A182 / ASME SA182 · F11 (K11572) · F22 (K21590) · F5 (K41545) · matching A234 WP11 / WP22 / WP5 fittingsF11: Cr 1.25 Mo 0.5 · F22: Cr 2.25 Mo 1 · F5: Cr 5 Mo 0.5Forged flanges, fittings and valve parts matching Cr-Mo pipe grades for high-temperature, hydrogen and sulphide-bearing service; tensile ≥485 MPa (Cl. 2).Refinery and petrochemical flanges, olets and fittings, power-plant piping components
A387 Gr. 11 / 22 Cr-Mo pressure-vessel plateASTM A387 / ASME SA387 Cl. 2 · 13CrMo4-5 / 10CrMo9-10 · EN 10028-2Gr. 11: Cr 1.25 Mo 0.5 · Gr. 22: Cr 2.25 Mo 1Chromium-molybdenum plate for elevated-temperature pressure vessels; Cl. 2 tensile 515–690 MPa, yield ≥310 MPa.Reactors, hydrocracker vessels, heat-exchanger shells, boiler drums

Also available on request: EN 16, EN 18, EN 9, 30MnCr5, 42CrMo4 QT plates and alloy steel fasteners to ASTM A193 B7 / A194 2H. Indian IS 1570 / IS 5517 designations are supplied against the EN / SAE grades above.

05TS

Tool & Die Steel

High-carbon alloy steels designed to be hardened for cutting, forming and moulding. Cold-work grades (D2, D3, D6, A2, O1) prioritise wear resistance; hot-work grades (H11, H13, DB6) resist thermal fatigue and softening; mould steel P20 is supplied pre-hardened, ready to machine; valve steels EN 52 and 21-4N resist heat and scaling. See the Tool & Die Steel page.

Forms: Round bars, flat bars, square bars, blocks, cut-to-size pieces, ground (silver steel) bars – annealed or pre-hardened

Standards: AISI / ASTM A681 · EN ISO 4957 · BS 4659 · IS 3749 · JIS G4404 · BS 1407 (silver steel)

GradeEquivalentsNominal CompositionKey PropertiesTypical Applications
D2 (HCHCr) Cold work · Air hardeningW.Nr. 1.2379 · X153CrMoV12 · BD2 · SKD 11 · IS XT160Cr12 (similar)C 1.55 · Cr 12 · Mo 0.8 · V 0.9High-carbon high-chromium, air-hardening; high wear resistance with better toughness than D3. Working hardness 58–62 HRC.Blanking and forming dies, punches, thread-rolling dies, shear blades, gauges, cold rolls
D3 (HCHCr) Cold work · Oil hardeningW.Nr. 1.2080 · X210Cr12 · BD3 · SKD 1C 2.1 · Cr 12Highest wear resistance of the HCHCr family; oil-hardening. Working hardness 58–64 HRC.Long-run blanking dies, drawing dies, brick moulds, shear blades, deep-drawing tools
D6 Cold work · W-bearingW.Nr. 1.2436 · X210CrW12 · BD6 · SKD 2C 2.1 · Cr 12 · W 0.7D3 with a tungsten addition for extra abrasion resistance and hardness retention; oil hardening. Working hardness 58–64 HRC.Blanking and punching tools, thread-rolling dies, cold rolls, measuring tools, plastic moulds
A2 Cold work · Air hardeningW.Nr. 1.2363 · X100CrMoV5 · BA2 · SKD 12C 1.0 · Cr 5.2 · Mo 1.1 · V 0.2Medium-alloy air-hardening steel with a better balance of toughness and wear resistance than D2, and minimal distortion. Working hardness 57–62 HRC.Punches and dies, shear blades, thread-rolling dies, forming rolls, gauges
O1 (OHNS) Cold work · Oil hardeningAISI O1 · W.Nr. 1.2510 · 100MnCrW4 · BO1 · SKS 3C 0.95 · Mn 1.1 · Cr 0.55 · W 0.55 · V 0.1Oil-hardening, non-shrinking – minimal distortion on hardening; easy to machine in the annealed state. Working hardness 57–62 HRC.Gauges, press tools, punches, measuring instruments, small dies, knives
H11 Hot workW.Nr. 1.2343 · X38CrMoV5-1 · BH11 · SKD 6C 0.38 · Cr 5 · Mo 1.3 · V 0.4 · Si 1.0Excellent toughness and resistance to thermal shock; air hardening. Working hardness 44–52 HRC.Forging dies, extrusion tooling and containers, die-casting dies, hot shear blades, high-strength structural parts
H13 Hot workW.Nr. 1.2344 · X40CrMoV5-1 · BH13 · SKD 61 · IS XT35Cr5MoV1 (similar)C 0.40 · Cr 5.2 · Mo 1.4 · V 1.0 · Si 1.0Higher vanadium than H11 for better hot-wear and thermal-fatigue resistance; the most widely used hot-work steel. Working hardness 44–52 HRC.Aluminium and zinc die-casting dies, extrusion dies, hot-forging tools, plastic moulds
P20 / P20+Ni Plastic mouldW.Nr. 1.2311 / 1.2738 · 40CrMnMo7 / 40CrMnNiMo8-6-4C 0.40 · Cr 1.9 · Mn 1.5 · Mo 0.2 (+ Ni 1.0 in 1.2738)Supplied pre-hardened (about 28–34 HRC) – machine, texture and polish without further heat treatment; P20+Ni gives uniform hardness in large blocks.Plastic injection moulds, blow moulds, die-casting holder blocks, mould bases
DB6 Hot work · Die blockW.Nr. 1.2714 · 55NiCrMoV7 · BH224/5 · SKT 4C 0.55 · Ni 1.7 · Cr 1.1 · Mo 0.5 · V 0.1Nickel-chromium-molybdenum die-block steel with high toughness through large sections; supplied annealed or pre-hardened (about 36–42 HRC).Hammer and press forging dies, die holders, bolsters, hot shear blades
S7 Shock resistingAISI S7 · W.Nr. 1.2355 (similar) · 50CrMoV13-15C 0.50 · Cr 3.25 · Mo 1.4 · V 0.25Air-hardening shock-resisting steel with outstanding impact toughness and good hot hardness. Working hardness 54–58 HRC.Chisels, punches, rivet sets, shear blades, cold and hot forming tools, plastic moulds
Silver Steel Precision ground barBS 1407 · W.Nr. 1.2210 (115CrV3, similar) · AISI W1 (similar)C 1.15 · Cr 0.45 · Mn 0.4 · V 0.1High-carbon steel supplied bright ground and polished to close tolerance (h8 / h9); water or oil hardening to about 62–64 HRC.Punches, pins, shafts, spindles, jigs and fixtures, tool-room work
EN 52 Valve steel · MartensiticBS 970 401S45 · X45CrSi9-3 (1.4718) · SUH 1 · UNS S65007C 0.45 · Si 3.0 · Cr 9.0 · Mn 0.5Silchrome valve steel with good resistance to scaling and oxidation up to about 800 °C; hardenable to about 300 HB.Intake valves, stems for bi-metal valves, high-temperature fasteners and shafts
21-4N Valve steel · AusteniticBS 970 349S54 · X53CrMnNiN21-9 (1.4871) · SUH 35 · UNS S63008C 0.53 · Mn 9 · Cr 21 · Ni 4 · N 0.4High-manganese austenitic valve steel with excellent hot strength, corrosion and scaling resistance; non-hardenable, age-hardens in service.Highly stressed exhaust and intake valves, hot-gas components, high-temperature fasteners

"HCHCr" is supplied as D2 or D3; "hot die steel" as H11 / H13 / DB6; "plastic mould steel" as P20 / P20+Ni. Other grades (D2M, O2, W-series, DIN 2714 modified) on request.

06HS

High Speed Steel

Highly alloyed tool steels that keep their hardness ("red hardness") at the temperatures reached in high-speed cutting. Tungsten (T) grades are the classic cutting steels; molybdenum (M) grades offer similar performance with better toughness and lower cost; cobalt grades (T4, T15, T42, M35, M42) add hot hardness for difficult materials; powder-metallurgy (PM) grades give a fine, uniform carbide structure. See the High Speed Steel page.

Forms: Round bars (black, peeled or ground), flats, squares, tool bits, blanks and cut pieces – annealed, larger sizes available for faster delivery

Standards: ASTM A600 · EN ISO 4957 · BS 4659 · IS 7291 · JIS G4403

GradeEquivalentsNominal CompositionKey PropertiesTypical Applications
T1 Tungsten HSS · 18-0-1W.Nr. 1.3355 · HS18-0-1 · BT1 · IS XT72W18Cr4V1 · SKH 2C 0.75 · W 18 · Cr 4 · V 1.1The original 18-4-1 high speed steel; good red hardness and grindability, moderate toughness. Working hardness 63–65 HRC.Turning, planing and slotting tools, taps, twist drills, threading dies, reamers, broaches
T4 Tungsten-cobalt HSSW.Nr. 1.3255 · HS18-1-2-5 · BT4 · IS XT75W18Co5Cr4MoV1 · SKH 3C 0.75 · W 18 · Cr 4 · V 1.1 · Co 5 · Mo 0.65Cobalt addition to T1 for higher hot hardness and wear resistance in heavy roughing cuts. Working hardness 64–66 HRC.Turning, planing and milling tools for roughing work, tool bits, form tools
T15 Tungsten-cobalt HSS · High VW.Nr. 1.3202 · HS12-1-5-5 · BT15C 1.50 · W 12.5 · Cr 4.5 · V 5 · Co 5Very high vanadium and cobalt for maximum abrasion resistance and red hardness; difficult to grind. Working hardness 65–67 HRC.Finishing and precision-cutting turning tools, form tools, tools for hard and abrasive materials
T42 Tungsten-cobalt HSS · SuperW.Nr. 1.3207 · HS10-4-3-10 · BT42 · IS XT125WCo10Cr4Mo4V3 · SKH 57C 1.25 · W 9.5 · Mo 3.6 · V 3.2 · Co 10 · Cr 4One of the hardest conventional high speed steels, with outstanding hot hardness for difficult-to-machine materials. Working hardness 66–68 HRC.Roughing and finishing tools for hardened and heat-resisting alloys, tool bits, wood-working tools, highly stressed cold-work tools
M2 Molybdenum HSS · 6-5-2W.Nr. 1.3343 · HS6-5-2 · BM2 · IS XT87W6Mo5Cr4V2 · SKH 51C 0.90 · W 6.4 · Mo 5 · Cr 4.1 · V 1.8The most widely used general-purpose high speed steel – good balance of hardness, toughness and wear resistance. Working hardness 62–65 HRC.Taps, twist drills, reamers, milling cutters, broaches, metal saws, wood-working and cold-work tools
M3 Class 2 Molybdenum HSS · High VW.Nr. 1.3344 · HS6-5-3 · BM4 (similar) · SKH 53C 1.20 · W 6.4 · Mo 5.1 · Cr 4.3 · V 3.3Higher carbon and vanadium than M2 for improved wear resistance and hardness retention. Working hardness 63–66 HRC.Broaches, reamers, milling cutters, taps, form tools, cold-work tooling for abrasive materials
M35 Molybdenum-cobalt HSSW.Nr. 1.3243 · HS6-5-2-5 · BM35 · IS XT90W6Co5Mo5Cr4V2 · SKH 55C 0.92 · W 6.4 · Mo 5 · Cr 4.1 · V 1.9 · Co 4.8M2 with 5% cobalt for higher hot hardness – the standard choice for stainless and high-tensile steels. Working hardness 64–66 HRC.Turning and planing tools, milling cutters, hobs, broaches, taps, twist drills, cold-work tools
M42 Molybdenum-cobalt HSS · SuperW.Nr. 1.3247 · HS2-10-1-8 · BM42 · IS XT110Mo10Co8Cr4W2 · SKH 59C 1.10 · Mo 9.5 · W 1.5 · Cr 3.9 · V 1.2 · Co 8High-cobalt molybdenum grade hardening to 67–69 HRC with excellent red hardness and good grindability for its hardness.Milling cutters, twist drills, taps, broaches, end mills for hard and heat-resisting materials, cold-work tools
ASP 23 / ASP 2023 PM HSSW.Nr. 1.3395 · HS6-5-3 PM · similar to M3:2 PMC 1.28 · W 6.4 · Mo 5 · Cr 4.2 · V 3.1Powder-metallurgy grade with fine, evenly distributed carbides – higher toughness, dimensional stability and grindability than conventional M3:2. Working hardness 60–65 HRC.Blanking and fine-blanking tools, cold-forming dies, knives, broaches, milling tools
ASP 30 / ASP 2030 PM HSS · CobaltW.Nr. 1.3294 · HS6-5-3-8 PMC 1.28 · W 6.4 · Mo 5 · Cr 4.2 · V 3.1 · Co 8.5Cobalt-bearing PM grade combining high hot hardness with the toughness of a PM structure. Working hardness 63–67 HRC.Gear-cutting tools (hobs, shaper cutters), end mills, taps, highly stressed cold-work tools
ASP 60 / ASP 2060 PM HSS · SuperHS6-7-6-10 PMC 2.3 · W 6.5 · Mo 7 · Cr 4 · V 6.5 · Co 10.5Very high carbide volume for maximum wear resistance and hot hardness among PM high speed steels. Working hardness 65–69 HRC.Tools for machining titanium, nickel alloys and hardened steels; form tools; cold-forming punches

Indian designations follow IS 7291 (e.g. XT72W18Cr4V1 = T1, XT87W6Mo5Cr4V2 = M2). ASP® is a trademark of Erasteel. If you require any grade in any size we can arrange it; larger sizes are generally available ex-stock for faster delivery.

07NF

Non-Ferrous Metals

Copper, brass and aluminium for conductivity, machinability and light weight; nickel alloys for seawater, acids and high temperature; titanium for the best strength-to-weight ratio with near-immunity to chloride corrosion; cupro-nickels and bronzes for marine and bearing service. See the Non-Ferrous Metals page.

Forms: Sheets, plates, coils, strips, seamless & welded pipes and tubes, round bars, flats, wire, fittings, flanges, fasteners, ingots

Standards: ASTM B152, B187, B16, B36, B209, B221, B160–B168, B443–B446, B574, B575, B622, B265, B338, B348, B171, B466 · EN 1652, EN 573, EN 12163 · IS 191, IS 410, IS 733

GradeEquivalentsNominal CompositionKey PropertiesTypical Applications
Copper C11000 ETP copperCu-ETP · CW004A · 2.0065 · IS 191 ETPCu ≥99.90Very high electrical conductivity (~100% IACS) and thermal conductivity; easily formed and brazed.Busbars, earthing strips, electrical contacts, heat-transfer equipment, roofing
Copper C10100 / C12200 OFE · DHP copperCu-OFE (CW009A) · Cu-DHP (CW024A) · 2.0040 / 2.0090Cu ≥99.99 (OFE) · Cu ≥99.90 + P 0.015–0.04 (DHP)Oxygen-free copper for vacuum and high-purity electrical use; phosphorus-deoxidised copper is weldable and brazeable without embrittlement.Vacuum and electronic parts (OFE); plumbing, refrigeration and medical-gas tubes, heat exchangers (DHP)
Brass C36000 Free-cutting brassCuZn36Pb3 · CW603N · 2.0375 · IS 319 Gr. 1Cu 61.5 · Pb 3 · Zn bal.Benchmark for machinability among copper alloys; good corrosion resistance.Turned components, valve bodies, plumbing fittings, fasteners, inserts
Brass C26000 70/30 cartridge brassCuZn30 · CW505L · 2.0265 · IS 410 CuZn30Cu 70 · Zn 30Excellent cold formability and ductility; good strength; bright finish.Deep-drawn parts, radiator cores, cartridge cases, lamp and hardware components
Naval Brass C46400 CuZn39Sn1CW719R · CuZn39Sn1 · 2.0530Cu 60 · Zn 39 · Sn 0.75Tin addition improves dezincification and seawater corrosion resistance; good strength and hot workability.Marine hardware, propeller shafts, condenser plates, valve stems, tube sheets
Aluminium 6061 Al-Mg-Si · T6UNS A96061 · EN AW-6061 · AlMg1SiCu · 3.3211 · IS 65032Mg 1.0 · Si 0.6 · Cu 0.28 · Cr 0.2Versatile heat-treatable structural alloy; tensile about 310 MPa in T6; good weldability, machinability and corrosion resistance.Structural frames, machined parts, fixtures, marine fittings, pneumatic components
Aluminium 6082 Al-Si-Mg-Mn · T6 (HE30)UNS A96082 · EN AW-6082 · AlSi1MgMn · 3.2315 · BS HE30 · IS 64430Si 1.0 · Mg 0.9 · Mn 0.7Highest strength of the common 6xxx alloys (tensile about 340 MPa in T6); good machinability and corrosion resistance.Highly stressed structures, bridges, cranes, transport components, machined blocks
Aluminium 7075 Al-Zn-Mg-Cu · T6UNS A97075 · EN AW-7075 · AlZn5.5MgCu · 3.4365Zn 5.6 · Mg 2.5 · Cu 1.6 · Cr 0.23One of the strongest aluminium alloys (tensile about 570 MPa in T6); excellent machinability; lower corrosion resistance than 6xxx.Aerospace parts, jigs and fixtures, moulds, high-stress machined components
Nickel 200 / 201 Commercially pure nickelUNS N02200 / N02201 · W.Nr. 2.4066 / 2.4068Ni ≥99.0 · C ≤0.15 (201: ≤0.02)Excellent resistance to caustic alkalis and reducing environments; magnetic; 201 (low carbon) for service above 315 °C.Caustic soda evaporators, food-processing equipment, electronic and electroplating components
Monel 400 Ni-CuUNS N04400 · W.Nr. 2.4360 · NiCu30FeNi ≥63 · Cu 31 · Fe ≤2.5Excellent resistance to seawater, hydrofluoric acid and alkalis; tough over a wide temperature range.Marine engineering, pumps and valves, HF-acid plants, heat exchangers
Monel K-500 Ni-Cu · Age-hardeningUNS N05500 · W.Nr. 2.4375 · NiCu30AlNi ≥63 · Cu 30 · Al 2.7 · Ti 0.6Corrosion resistance of Monel 400 with much higher strength and hardness after age-hardening (tensile about 1000 MPa).Pump shafts, impellers, oil-well tools, springs, marine fasteners
Inconel 600 Ni-Cr-FeUNS N06600 · W.Nr. 2.4816 · NiCr15FeNi ≥72 · Cr 15.5 · Fe 8Resists oxidation, carburisation and chloride stress-corrosion cracking; good strength at high temperature.Furnace muffles, heat-treatment baskets, chemical and food processing, nuclear components
Inconel 625 Ni-Cr-Mo-NbUNS N06625 · W.Nr. 2.4856 · NiCr22Mo9NbNi ≥58 · Cr 21.5 · Mo 9 · Nb 3.6High strength without age-hardening; exceptional pitting, crevice and seawater corrosion resistance; service from cryogenic to 980 °C.Marine and offshore hardware, chemical plants, aerospace ducting, flue-gas systems
Inconel 718 Precipitation-hardeningUNS N07718 · W.Nr. 2.4668 · NiCr19Nb5Mo3Ni 52.5 · Cr 19 · Nb 5.1 · Mo 3 · Ti 0.9 · Fe bal.Age-hardenable for very high strength up to about 650 °C; good weldability.Gas-turbine and aerospace parts, high-strength fasteners, oil-tool components
Incoloy 800 / 800H Ni-Fe-Cr · Heat resistingUNS N08800 / N08810 · W.Nr. 1.4876 / 1.4958 · X10NiCrAlTi32-21Ni 32 · Cr 21 · Fe bal. · Al + Ti 0.3–1.2Resists oxidation, carburisation and sulphidation at high temperature; 800H has controlled grain size for creep strength above 600 °C.Furnace components, heat-exchanger and reformer tubes, petrochemical furnace piping
Incoloy 825 Ni-Fe-Cr-Mo-CuUNS N08825 · W.Nr. 2.4858 · NiCr21MoNi 42 · Cr 21.5 · Mo 3 · Cu 2.2 · Ti 0.9 · Fe bal.Excellent resistance to sulphuric and phosphoric acids, chloride stress-corrosion cracking and pitting; stabilised against sensitisation.Acid-plant piping, pickling equipment, oil & gas downhole tubing, pollution-control equipment
Hastelloy C-276 Ni-Mo-CrUNS N10276 · W.Nr. 2.4819 · NiMo16Cr15WMo 16 · Cr 15.5 · W 3.75 · Fe 5.5 · Ni bal.Outstanding resistance to wet chlorine, hypochlorite, ferric and cupric chlorides and strong oxidisers.Chemical processing, pollution-control and FGD systems, pulp bleaching, waste treatment
Hastelloy C-22 Ni-Cr-Mo-WUNS N06022 · W.Nr. 2.4602 · NiCr21Mo14WCr 21 · Mo 13.5 · W 3 · Fe 3 · Ni bal.Versatile resistance in both oxidising and reducing media; excellent against pitting and crevice corrosion.Pharmaceutical and chemical reactors, scrubbers, pickling equipment
Titanium Grade 2 Commercially pureUNS R50400 · W.Nr. 3.7035 · Ti2Ti ≥99 · Fe ≤0.30 · O ≤0.25Excellent corrosion resistance in seawater and oxidising acids; good formability and weldability; tensile ≥345 MPa. Sheets 1–25 mm and tubes OD 6–25 mm regularly stocked.Heat exchangers, condensers, chemical process equipment, desalination, anodes
Titanium Grade 5 Ti-6Al-4VUNS R56400 · W.Nr. 3.7165 · TiAl6V4Al 6 · V 4 · Ti bal.High-strength titanium alloy (tensile ≥895 MPa) with low density; heat-treatable.Aerospace structures, medical implants, high-performance fasteners, motorsport
Cupro-Nickel 90/10 CuNi10Fe1MnUNS C70600 · CW352H · 2.0872 · IS 1545 (similar)Cu 88.5 · Ni 10 · Fe 1.4 · Mn 0.8Excellent seawater corrosion and biofouling resistance; good thermal conductivity and weldability.Seawater piping, condenser and heat-exchanger tubes, desalination plants, ship systems
Cupro-Nickel 70/30 CuNi30Mn1FeUNS C71500 · CW354H · 2.0882Cu 68.5 · Ni 30 · Fe 0.6 · Mn 0.8Higher strength and resistance to high-velocity seawater than 90/10.Condenser tubes, feedwater heaters, offshore firewater and seawater systems
Aluminium Bronze AB2 Nickel-aluminium bronzeBS 1400 AB2 · EN CuAl10Fe5Ni5 (CC333G) · UNS C95500 / C63000 (similar)Cu bal. · Al 9.5 · Ni 5 · Fe 5High strength (tensile about 640 MPa), excellent wear and seawater corrosion resistance, resists cavitation.Pump impellers and bodies, valve seats, bushes, gears, marine propellers, wear rings
Gunmetal LG2 Leaded gunmetalBS 1400 LG2 · EN CuSn5Zn5Pb5 (CC491K) · UNS C83600 · IS 318 Gr. 2Cu 85 · Sn 5 · Zn 5 · Pb 5Good machinability, pressure tightness and bearing properties; corrosion resistant in water and steam.Bushes, bearings, valve and pump bodies, pipe fittings, glands
Phosphor Bronze PB1 / C51000 Tin bronzeBS 1400 PB1 · CuSn5 (CW451K) / CuSn10-P (CC481K) · UNS C51000 / C90700Cu bal. · Sn 5–10 · P 0.1–0.4High fatigue strength, elasticity and wear resistance; good corrosion resistance; excellent bearing properties in cast form.Springs, bushes, bearings, worm wheels, electrical connectors, gears

Inconel®, Monel® and Incoloy® are trademarks of Special Metals Corporation; Hastelloy® is a trademark of Haynes International. Material is supplied to the UNS number and specification on your order. Lead, zinc, tin and beryllium copper are available on request.

Selection Guide

Which Grade for Which Job?

A starting point for common requirements. Final selection should consider the full service conditions – our team can help.

Seawater & Chlorides

316L · Duplex 2205 · Super Duplex 2507 · Cu-Ni 90/10 · Monel 400 · Titanium Gr 2

High-Temperature Oxidation

SS 310S · SS 309S · SS 321 · Incoloy 800H · Inconel 600 / 625

Aggressive Chemicals & Acids

SS 904L · Incoloy 825 · Hastelloy C-276 / C-22 · Inconel 625 · Titanium Gr 2

High-Tensile Shafts

EN 19 / 4140 · EN 24 / 4340 · C45 · EN 8 (lighter duty)

Case-Hardened Gears

20MnCr5 · 16MnCr5 · EN 353 · SAE 8620 · EN 36

Bearings & Rollers

EN 31 / 52100 · Gunmetal LG2 · Phosphor Bronze

Cold-Work Dies & Punches

D2 · D3 · D6 · A2 · O1 (OHNS) · Silver Steel

Hot-Work & Die-Casting

H13 · H11 · DB6 · S7

Plastic Moulds

P20 / P20+Ni (pre-hardened) · H13 · SS 420

Cutting Tools

M2 (general) · M35 (stainless) · M42 / T42 (hard materials) · ASP 23 / 30 (PM)

Structural Fabrication

IS 2062 E250 / E350 · S355J2 · IS 1239 / IS 1161 tubes · A36

Low-Temperature Service

A333 Gr. 6 · A350 LF2 · A420 WPL6 · SS 304L / 316L

Boilers & Pressure Vessels

SA 516 Gr. 70 · A106 Gr. B · SA 210 · P11 / P22 / P91 · A387

Engine & Valve Steels

EN 52 (inlet) · 21-4N (exhaust) · EN 47 (springs) · EN 24

High-Speed Machining

EN 1A Leaded · SS 303 / 416 · Brass C36000

Electrical Conductivity

Copper C11000 / C10100 · Aluminium 6061 / 6082

Lightweight Strength

Titanium Gr 5 · Aluminium 7075 · Aluminium 6082

Scratch-Free Fabrication

PVC-coated SS 304 & 316 sheets – our speciality for kitchens, pharma and architectural work

Get in Touch

Need a Material in a Specific Grade or Size?

Send us the product, grade, size, quantity and delivery location – our team replies with stock status and a competitive quote, usually the same working day.