Mon – Sat · 10:00 am – 7:00 pm

Non-Ferrous Metals

Copper, brass, aluminium, nickel & nickel alloys (Monel, Inconel, Incoloy, Hastelloy), titanium, cupro-nickel and bronzes – imported and stocked in Mumbai as sheets, plates, pipes, tubes, round bars, fittings and flanges, supplied with mill test certificates.

30+ Alloys Sheet · Pipe · Bar · Fittings EN 10204 3.1 MTC
Non-ferrous round bars and rods stacked in a warehouse
RangeCu · Brass · Al · Ni · Ti · Cu-Ni · Bronze FormsSheet · Plate · Pipe · Tube · Bar CertsEN 10204 3.1 · TPI on request
Overview

Metals for Corrosion, Conductivity & Heat Transfer

Non-ferrous metals contain little or no iron. They are chosen where steel falls short – for electrical and thermal conductivity (copper, aluminium), for seawater and acid resistance (cupro-nickel, titanium, Hastelloy), for high-temperature strength (Inconel, Incoloy) or for low weight (aluminium, titanium).

Honesty Impex has imported, stocked and supplied non-ferrous metals and high-nickel alloys since 2000. Material is held in Mumbai in sheet, plate, coil, pipe, tube, round bar, fittings and flange form, and dispatched with mill test certificates traceable to the heat or cast number. Third-party inspection by agencies such as Bureau Veritas, DNV, Lloyd's Register, TÜV or EIL can be arranged at the time of order.

  • Copper, brass, aluminium & bronzes from stock
  • Nickel, Monel, Inconel, Incoloy & Hastelloy
  • Titanium sheets 1 – 25 mm, tubes OD 6 – 25 mm
  • Cut-to-size, PMI-verified, certified material

Quick Facts

Families
Copper & alloys, aluminium, nickel & Ni-alloys, titanium, lead & zinc
Forms
Sheet, plate, coil, strip, pipe, tube, round bar, flat, fittings, flanges, wire
Specifications
ASTM B-series, ASME SB, EN, DIN, BS, IS, JIS
Identification
UNS numbers, EN CW/CC numbers, W.Nr 2.4xxx / 3.7xxx
Certification
EN 10204 3.1 (3.2 with TPI), PMI reports on request
Supply
Ex-stock Mumbai; imports arranged for project quantities

Choosing the Right Non-Ferrous Metal

A quick guide to which family fits which duty. Final selection should always follow the design code and the process conditions.

RequirementRecommended familyWhy
Electrical conductivityCopper C110 / ETP, aluminium 1100 / 6101Copper ETP ≈ 100% IACS; aluminium gives ~60% IACS at a third of the weight
Seawater & brineCupro-nickel 90/10 & 70/30, titanium Gr.2, Monel 400, aluminium bronzeResist pitting, crevice attack and biofouling in chloride service
Hot concentrated acidsHastelloy C-276 / C-22 (oxidising & reducing), B-2 (hydrochloric)Ni-Mo-Cr alloys tolerate mixed and reducing acids that attack stainless steel
High temperature (> 600 °C)Inconel 600 / 601 / 625, Incoloy 800H / 800HTRetain strength and resist oxidation and carburisation up to 1100 – 1200 °C
High strength + corrosionInconel 718, Monel K-500, titanium Gr.5, aluminium 7075-T6Precipitation-hardened or alpha-beta alloys with strength-to-weight advantages
Bearings & bushesPhosphor bronze, gunmetal LG2, aluminium bronze AB2Low friction, good wear resistance and embeddability against steel shafts
Light structures & transportAluminium 5052, 6061-T6, 6082-T6Weldable, formable alloys with good strength-to-weight and marine resistance
Alloys & Grades

Non-Ferrous Alloys We Stock

Nominal compositions in weight %; balance is the base metal. Equivalents are the closest common designations – confirm the exact specification on your order.

AlloyEquivalentsNominal CompositionKey PropertiesTypical Uses
Copper ETP (C101)C11000 · CW004A · Cu-ETP · IS 191 Cu-ETPCu ≥ 99.90, O ~0.04≥ 100% IACS conductivity, excellent thermal conductivity, soft & ductileBusbars, earthing strips, electrical sheets, roofing, heat-transfer components
Copper DHP (C106)C12200 · CW024A · Cu-DHPCu ≥ 99.90, P 0.015 – 0.040Weldable & brazeable without embrittlement, ~85% IACSPlumbing & refrigeration tube, heat exchangers, pressure vessels, PVC-coated copper tube
Free-Cutting Brass (CZ121)C36000 · CW614N · CuZn39Pb3 · IS 319 Gr.1Cu 58, Pb 3, Zn bal.100% machinability rating, good strengthTurned parts, valve bodies, fittings, fasteners, inserts
Brass 63/37 & 70/30C27200 / C26000 · CW508L / CW505L · CZ108 / CZ106Cu 63 or 70, Zn bal.Deep-drawing (cartridge) quality, bright finishSheets, strips, tubes, radiator cores, decorative & architectural work
Naval Brass (CZ112)C46400 · CW712R · CuZn38Sn1Cu 60, Sn 1, Zn bal.Tin addition resists dezincification in seawaterMarine hardware, tube sheets, condenser plates, propeller shafts
Aluminium 1100 / 1050IS 19000 · EN AW-1100 · A91100Al ≥ 99.0Highest formability & conductivity among Al grades, excellent corrosion resistanceChemical equipment, heat-exchanger fins, cladding, reflectors
Aluminium 5052-H32IS 52000 · EN AW-5052 · A95052Mg 2.5, Cr 0.25Best weldable marine-grade sheet, good fatigue strengthBoat hulls, tanks, pressure vessels, panels, truck bodies
Aluminium 6061-T6IS 65032 · EN AW-6061 · A96061Mg 1.0, Si 0.6, Cu 0.28, Cr 0.2UTS ≈ 310 MPa, heat-treatable, weldable, anodises wellStructural sections, machined parts, jigs & fixtures, automotive
Aluminium 6082-T6 (HE30)IS 64430 · EN AW-6082 · BS HE30 / H30Mg 0.9, Si 1.0, Mn 0.7Highest strength of the 6000 series (UTS ≈ 340 MPa), good machinabilityBridges, cranes, transport, high-stress structural plate & bar
Aluminium 7075-T6IS 74530 · EN AW-7075 · A97075Zn 5.6, Mg 2.5, Cu 1.6, Cr 0.23UTS ≈ 570 MPa – one of the strongest Al alloysAerospace, moulds, tooling plates, high-performance components
Aluminium 2024-T351IS 24345 · EN AW-2024 · A92024Cu 4.4, Mg 1.5, Mn 0.6High strength & fatigue resistance; limited corrosion resistance (often clad)Aircraft structures, rivets, precision machined parts
Nickel 200 / 201N02200 / N02201 · 2.4066 / 2.4068 · LC-Ni 99Ni ≥ 99.0 (201: C ≤ 0.02)Resists caustic alkalis, ferromagnetic; 201 for service above 315 °CCaustic evaporators, food processing, electronic & electroplating equipment
Monel 400N04400 · 2.4360 · NiCu30Fe · BS 3072 NA13Ni 63, Cu 31, Fe 2.5, Mn 2Outstanding in seawater, HF & de-aerated acids; UTS ≈ 550 MPaSeawater valves & pumps, HF alkylation, heat exchangers, marine fasteners
Monel K-500N05500 · 2.4375 · NiCu30Al3TiNi 63, Cu 30, Al 2.7, Ti 0.6Age-hardenable to UTS ≈ 1100 MPa, non-magnetic, Monel 400 corrosion resistancePump & propeller shafts, oil-well tools, springs, fasteners
Inconel 600N06600 · 2.4816 · NiCr15Fe · BS 3072 NA14Ni 72, Cr 15.5, Fe 8Oxidation & chloride-SCC resistance to 1100 °C; resists causticFurnace muffles, heat-treatment fixtures, nuclear steam generators, chemical plant
Inconel 601N06601 · 2.4851 · NiCr23FeNi 61, Cr 23, Fe 14, Al 1.4Superior oxidation & spalling resistance to 1200 °CRadiant tubes, furnace baskets, burner components, thermal reactors
Inconel 625N06625 · 2.4856 · NiCr22Mo9Nb · Gr.1 & Gr.2Ni 61, Cr 21.5, Mo 9, Nb 3.6Very high strength & fatigue resistance, immune to chloride pitting; cryogenic to 980 °COffshore risers, flue-gas scrubbers, aerospace ducting, overlay cladding, bellows
Inconel 718N07718 · 2.4668 · NiCr19Fe19Nb5Mo3Ni 52.5, Cr 19, Fe 18, Nb 5, Mo 3, Ti 0.9Precipitation-hardened, UTS ≈ 1240 MPa, usable −250 °C to 700 °CGas-turbine discs, downhole tools, high-strength fasteners, cryogenic tanks
Incoloy 800 / 800H / 800HTN08800 / N08810 / N08811 · 1.4876 / 1.4958 / 1.4959 · X10NiCrAlTi32-21Ni 32, Cr 21, Fe bal., Al+TiCreep-rupture strength & carburisation resistance at 600 – 1000 °CReformer & pyrolysis tubes, superheaters, heat-treatment furnaces
Incoloy 825N08825 · 2.4858 · NiCr21MoNi 42, Cr 21.5, Fe 30, Mo 3, Cu 2.2, Ti 0.9Resists sulphuric & phosphoric acids, chloride SCC and pittingAcid pickling, pollution-control, oil & gas sour-service piping, nuclear fuel reprocessing
Hastelloy C-276N10276 · 2.4819 · NiMo16Cr15WNi 57, Mo 16, Cr 16, W 4, Fe 5Broadest resistance to oxidising & reducing media, wet chlorine, hypochloriteFGD scrubbers, chemical reactors, pulp & paper bleach plants, waste treatment
Hastelloy C-22N06022 · 2.4602 · NiCr21Mo14WNi 56, Cr 22, Mo 13, W 3, Fe 3Better than C-276 in oxidising media & crevice conditions; weld-friendlyPharmaceutical reactors, acid handling, incinerator scrubbers, cellulose acetate plant
Hastelloy B-2 / B-3N10665 / N10675 · 2.4617 / 2.4600 · NiMo28Ni 69, Mo 28, Fe ≤ 2Exceptional in hydrochloric acid at all concentrations & temperatures (reducing only)HCl handling, acetic acid, sulphuric acid at moderate concentration
Titanium Gr.1 / Gr.2R50250 / R50400 · 3.7025 / 3.7035 · CP TiTi ≥ 99.2 (Gr.2: O ≤ 0.25, Fe ≤ 0.30)Gr.2: UTS ≥ 345 MPa, density 4.51 g/cm³, immune to seawater & wet chlorineCondenser tubes, heat exchangers, chlor-alkali cells, desalination, anodes
Titanium Gr.5 (Ti-6Al-4V)R56400 · 3.7165 · TiAl6V4Al 6, V 4, Ti bal.UTS ≥ 895 MPa, heat-treatable, best strength-to-weight ratioAerospace & defence, pressure vessels, medical implants, high-performance fasteners
Cupro-Nickel 90/10C70600 · CW352H · CuNi10Fe1Mn · BS CN102Cu 88.6, Ni 10, Fe 1.4, Mn 1Seawater corrosion & biofouling resistance, good weldabilitySeawater piping, condenser & cooler tubes, desalination, offshore firewater
Cupro-Nickel 70/30C71500 · CW354H · CuNi30Mn1Fe · BS CN107Cu 68, Ni 30, Fe 0.7, Mn 1Higher strength & velocity tolerance than 90/10High-velocity seawater systems, naval piping, heat-exchanger tubes
Aluminium Bronze AB2C95800 / C63000 · CC333G / CW307G · CuAl10Ni5Fe4 · IS 305 AB2Al 9 – 10, Ni 4.5 – 5, Fe 4, Mn 1UTS ≈ 600 – 700 MPa, excellent wear, cavitation & seawater resistancePump & valve components, propellers, gears, bushes, wear plates, non-sparking tools
Gunmetal LG2C83600 · CC491K · CuSn5Zn5Pb5 · IS 318 LTB2Cu 85, Sn 5, Zn 5, Pb 5Pressure-tight castings, good machinability & bearing propertiesValve bodies, pump casings, bushes, steam fittings, bearings
Phosphor Bronze PB1 / PB102C51000 / C52100 · CW451K / CW453K · CuSn5 / CuSn8Sn 5 – 8, P 0.1 – 0.35High fatigue strength, spring quality, low frictionSprings, bearings, bushes, gears, electrical contacts, wear strips
Lead & ZincPb 99.97 IS 27 · Zn 99.95 IS 209Commercially pureLead: radiation shielding & acid resistance; zinc: sacrificial protectionLead sheets, pipes & linings; zinc anodes, sheets & galvanising
Forms & Sizes

Products Available in Non-Ferrous Metals

Typical stock ranges. Sizes outside these ranges and project quantities are arranged against order.

PIPE & TUBE

Pipes & Tubes

Seamless and welded pipe and tube in copper, cupro-nickel, nickel alloys and titanium; PVC-coated copper tube for refrigeration and gas lines.

  • Sizes Tube OD 6 – 108 mm; pipe NPS ⅛" – 12" (Sch 5S – 160); titanium tube OD 6 – 25 mm
  • Standards ASTM B88, B111, B466, B161, B165, B167, B444, B622, B338, B861; IS 2501, IS 1545; EN 12449
SHEET & PLATE

Sheets & Plates

Hot and cold rolled sheets, plates, coils and strips in copper, brass, aluminium, nickel alloys, cupro-nickel and titanium.

  • Sizes 0.3 – 100 mm thick; widths to 2000 mm; titanium 1 – 25 mm thick
  • Standards ASTM B152, B36, B209, B162, B127, B168, B443, B575, B265; IS 191, IS 410, IS 737; EN 1652
ROUND BAR

Round Bar

Extruded, drawn and forged round, hex, square and flat bar in brass, copper, aluminium, bronze, nickel alloys and titanium.

  • Sizes Ø 3 – 300 mm; flats & squares to order; hollow bar in bronze
  • Standards ASTM B16, B150, B211, B160, B164, B166, B446, B637, B348; IS 733, IS 319; EN 12164 / 12167
FITTINGS

Fittings

Butt-weld, socket-weld and threaded elbows, tees, reducers, caps and stub ends in cupro-nickel, Monel, Inconel, Hastelloy, titanium and copper.

  • Sizes ½" – 12" butt weld; ⅛" – 2" forged (3000 / 6000 lb)
  • Standards ASTM B366, B361, B122; ASME B16.9, B16.11; EN 1254 (copper)
FLANGES

Flanges

Weld-neck, slip-on, blind, lap-joint and socket-weld flanges in copper alloys, cupro-nickel, nickel alloys, aluminium and titanium.

  • Sizes ½" – 24", Class 150 – 1500; PN 10 – PN 40
  • Standards ASTM B462, B564, B381, B247, B171 (plate); ASME B16.5, B16.47
FASTENERS

Fasteners

Bolts, nuts, studs and washers in brass, silicon bronze, Monel 400 / K-500, Inconel 625 / 718, Hastelloy C-276 and titanium Gr.2 / Gr.5.

  • Sizes M3 – M64 and ¼" – 2½"; special lengths to drawing
  • Standards ASTM F468 / F467, B164, B637; DIN 931 / 933 / 934; ISO 4014 / 4032

Non-ferrous and high-nickel material is stored and handled separately from carbon steel to prevent iron contamination. Use the weight chart for copper, brass, aluminium and titanium densities when estimating quantities.

Standards

Specifications We Supply To

ASTM B-series specifications are also available as ASME SB equivalents for pressure-vessel and piping code work.

ASTM B152 / B36Copper sheet, strip & plate / brass plate, sheet & strip
ASTM B88Seamless copper water tube (Types K, L, M)
ASTM B111 / B466Copper & cupro-nickel condenser tubes / seamless Cu-Ni pipe & tube
ASTM B209 / B211Aluminium & aluminium-alloy sheet & plate / bar, rod & wire
ASTM B160 / B161 / B163Nickel rod & bar / seamless pipe & tube / condenser tubes (Ni & Ni-alloy)
ASTM B165 / B167Monel 400 seamless pipe & tube / Inconel 600-601 seamless pipe & tube
ASTM B443 / B444Inconel 625 plate, sheet & strip / seamless pipe & tube
ASTM B575 / B622Hastelloy plate, sheet & strip / seamless Ni-alloy pipe & tube
ASTM B265 / B338 / B348Titanium plate & sheet / heat-exchanger tube / bars & billets
IS 191 / IS 410 / IS 733Copper / brass sheet & strip / aluminium bars, rods & sections
IS 2501 / IS 1545Solid-drawn copper tubes for general purposes / for heat exchangers & condensers
EN 12449 / EN 1652 / EN 573Seamless copper tubes / copper plate & sheet / aluminium alloy designation system

See the full standards directory

Applications

Where Non-Ferrous Metals Are Used

Industries we regularly supply from our Mumbai stock, and the alloys they ask for most.

Chemical & Petrochemical

Hastelloy C-276 · Inconel 625 · Incoloy 825 · Nickel 200

Marine & Shipbuilding

Cu-Ni 90/10 · Naval brass · Aluminium bronze · Al 5052

Power & Desalination

Titanium Gr.2 · Cu-Ni 70/30 · Admiralty brass · Copper DHP

Electrical & Switchgear

Copper ETP busbar · Brass · Aluminium 1100 / 6101

Furnaces & Heat Treatment

Inconel 600 / 601 · Incoloy 800H · Nichrome

Pharma, Fertiliser & Paper

Hastelloy C-22 · Titanium · Monel 400 · Copper

Pumps, Valves & Bearings

Gunmetal LG2 · Phosphor bronze · AB2 · Monel K-500

Aerospace & Defence

Ti-6Al-4V · Inconel 718 · Al 7075 / 2024

FAQ

Non-Ferrous Metals – Common Questions

Practical answers for buyers and engineers. For anything specific to your process, send us the conditions and we will advise.

  1. 1
    Alloy & specificatione.g. ASTM B165 UNS N04400 or Cu-Ni 90/10 C70600
  2. 2
    Form & sizeSheet thickness × width × length; pipe NPS/Sch or OD × wall; bar diameter
  3. 3
    Temper / conditionAnnealed, half-hard, T6, solution treated, aged
  4. 4
    QuantityKilograms, pieces or metres
  5. 5
    CertificationEN 10204 3.1 / 3.2, PMI, TPI agency
  6. 6
    DeliveryDestination and required date

Frequently Asked Questions

Monel, Inconel, Incoloy, Hastelloy – what is the difference?

All four are nickel-based alloy families. Monel is nickel-copper (seawater, hydrofluoric acid). Inconel is nickel-chromium (high temperature, oxidation). Incoloy is nickel-iron-chromium (economical high-temperature and acid service). Hastelloy is nickel-molybdenum-chromium (the most aggressive chemical environments). Each is identified unambiguously by its UNS number, which is what we quote and certify against.

Which titanium grade should I order for a heat exchanger?

Commercially pure Grade 2 is the standard choice for seawater condensers, chlor-alkali cells and chemical heat exchangers: it is weldable, formable and fully resistant to chlorides. Grade 5 (Ti-6Al-4V) is used only where high strength is needed. We stock Grade 2 sheets from 1 to 25 mm and tubes from OD 6 to 25 mm.

Cupro-nickel 90/10 or 70/30 for seawater piping?

90/10 (C70600) handles most seawater systems economically up to about 3 m/s flow velocity. 70/30 (C71500) is stronger and tolerates higher velocities and more turbulent conditions, so it is specified for naval and high-velocity systems. Both resist biofouling, which titanium and stainless do not.

How do you prevent mix-ups between alloys that look alike?

Every item carries the mill marking and heat / cast number, and we can perform positive material identification (PMI) by XRF before dispatch so the alloy you receive is verified against the certificate. Nickel alloys and titanium are stored separately from carbon steel.

Can you supply small quantities or cut pieces?

Yes. Because stock is maintained in Mumbai, we supply cut-to-size sheet, plate and bar for maintenance and fabrication jobs as well as full project quantities, with certificates for every piece.

Get in Touch

Need a Material in a Specific Grade or Size?

Send us the product, grade, size, quantity and delivery location – our team replies with stock status and a competitive quote, usually the same working day.